- Offer Profile
- Welcome to METALLUX AG, a
technological leader in linear and rotary sensors, resistors, pressure
sensors and industrial joysticks in thick-film technology. For more than
three decades, we have been dedicated to the needs of our customers from
around the entire world. The METALLUX guiding principle defines our actions:
a fair partnership for a long-term business connection, combined with
personalised and individual consultation for every business partner. Our
high-quality products and innovative system solutions are held in high
regard in the automotive field, medical technology, industry, wind and solar
energy and many other fields. This is due in no small part to our consistent
alignment of all developments with the needs of our customers. The Metallux
team looks forward to collaborating with you in developing a customised
solution for your needs.
Visit us on:
Pressure Sensors
- We develop and produce pressure measuring cells and pressure transmitters with tried-and-tested thick-film technology to measure the pressure in gaseous and liquid media.
Our products are compact, robust and reliable and deliver precise measured values, even under high load from temperature or corrosive media.
We not only offer a comprehensive range of standard products for the most diverse pressure ranges and applications, but also develop tailor-made, individual solutions to suit your exact requirements and installation conditions. Pressure Sensors in steel
Stainless steel pressure measuring cell SPS 1000
-
Monolithic stainless steel pressure measuring cell with a diameter of 18 mm, ideal for measuring relative pressure. It is available for pressure ranges from 10 to 1000 bar.
Stainless steel pressure measuring cells have particularly good properties in terms of overload capability and burst pressure behaviour. They also have an above-average media resistance and are therefore ideal for use with aggressive media.
- Very high media resistance
- Suitability for use in aggressive media
- Extremely high bursting strength
- High measurement accuracy
- Insensitive to pressure peaks
- Resistance to excess and negative pressure
- Good thermal stability
- Excellent long-term stability
- Compact design
- Very good price-performance ratio
- Easy to integrate
Stainless steel pressure measuring cell SPS 1000 Z with output amplifier
-
The monolithic stainless steel pressure measuring cell with a diameter of 18 mm is ideal for measuring relative pressure. It can be used for pressure ranges of 10 to 1,000 bar, features signal amplification and is supplied with a ratiometric output signal of 0.5 V to 4.5 V.
Stainless steel pressure measuring cells have particularly good properties in terms of overload capability and burst pressure behaviour. The sensors are also characterised by their above-average media resistance and are therefore ideal for use with aggressive media.
- Very high media resistance
- Suitability for use in aggressive media
- Extremely high bursting strength
- High measurement accuracy
- Insensitive to pressure peaks
- Resistance to excess and negative pressure
- Good thermal stability
- Excellent long-term stability
- Compact design
- Very good price-performance ratio
- Easy to integrate
Stainless steel pressure measuring cell SPS 3003 with process connection
-
The stainless steel pressure measuring cell with process connection is ideal for measuring relative pressure and is suitable for pressure ranges from 40 to 1,000 bar.
It is extremely resistant to burst and excess pressure as well as pressure peaks. Thanks to its above-average media resistance, it is ideal for use with aggressive media. High burst pressure resistance is an important property in hydraulic applications.
- Very high media resistance
- Suitability for use in aggressive media
- Extremely high bursting strength
- High measurement accuracy
- Insensitive to pressure peaks
- Resistance to excess and negative pressure
- Good thermal stability
- Excellent long-term stability
- Compact design
- Very good price-performance ratio
- Easy to integrate
Stainless steel pressure measuring cell SPS 3003 Z signal-amplified with process connection and output amplifier
-
The stainless steel pressure measuring cell is ideal for measuring relative pressure and is available for pressure ranges from 40 to 1,000 bar. It is signal-amplified and is supplied with a ratiometric output signal of 0.5 V to 4.5 V.
Stainless steel pressure measuring cells have particularly good properties in terms of overload capability and burst pressure behaviour. They also have an above-average media resistance and are therefore ideal for use with aggressive media.
- Very high media resistance
- Suitability for use in aggressive media
- Extremely high bursting strength
- High measurement accuracy
- Insensitive to pressure peaks
- Resistance to excess and negative pressure
- Good thermal stability
- Excellent long-term stability
- Compact design
- Very good price-performance ratio
- Easy to integrate
Pressure Sensors in ceramic
Ceramic pressure measuring cell CPS 1184
-
The monolithic ceramic pressure measuring cell with a diameter of 18 mm is ideal for measuring pressures of -1 to 600 bar.
Available with grid dimensions of 1.27 or 2.54 mm and as a Z variant with signal amplification (see CPS 1184 Z)Available connections: tin-plated solder pad, solder pin or ribbon cable
- High measurement accuracy
- Fast response time
- Very good media resistance
- Resistance to excess and negative pressure
- High bursting strength
- Good thermal stability
- Excellent long-term stability
- Compact design
- Simple assembly
- Very good price-performance ratio
Ceramic pressure measuring cell CPS 1184 Z with output amplifier
-
The monolithic ceramic pressure measuring cell with a diameter of 18 mm is ideal for measuring pressures of -1 to 600 bar. It features signal amplification and is supplied with a ratiometric output signal of 0.5 V to 4.5 V.
- High measurement accuracy
- Very good media resistance
- Resistance to excess and negative pressure
- High bursting strength
- Good thermal stability
- Excellent long-term stability
- Compact design
- Simple assembly
- Very good price-performance ratio
Ceramic pressure measuring cell CPS 2184
-
The ceramic pressure measuring cell with flush-mounted membrane and a diameter of 18 mm is ideal for measuring relative and absolute pressure as well as sealed gauge.
It is available for pressure ranges from -1 to 600 bar.
It is also available as a Z variant with signal amplification (see CPS 2184Z).
Available connections: tin-plated solder pad, solder pin or ribbon cable
- High measurement accuracy
- Very good media resistance
- Excellent corrosion resistance to aggressive media
- Resistance to excess and negative pressure
- High bursting strength
- Good thermal stability
- Excellent long-term stability
- Compact design
- Simple assembly
- Very good price-performance ratio
Pressure Sensor, ceramic, standard, ,5 - 600 bar with flush mounted membrane 0,5- 4,5 V CPS 2184 Z
-
The ceramic pressure measuring cell with flush-mounted membrane and a diameter of 18 mm is ideal for measuring relative and absolute pressure as well as sealed gauge. It can be used for pressure ranges from -1 to 600 bar.
It features signal amplification and is supplied with an output signal of 0.5 V to 4.5 V.Available connections: tin-plated solder pad, solder pin or ribbon cable
- High measurement accuracy
- Very good media resistance
- Excellent corrosion resistance to aggressive media
- Resistance to excess and negative pressure
- High bursting strength
- Good thermal stability
- Excellent long-term stability
- Compact design
- Simple assembly
- Very good price-performance ratio
Pressure Transmitter
Pressure transmitter MTX-F
-
The pressure transmitter consists of a ceramic pressure measuring cell and a robust, media-resistant stainless steel housing with a very small diameter. It is suitable for measuring relative pressure and is available in a pressure range from -1 to 150 bar. The low installation height and the compact design allow it to be used in a wide range of applications.
Mechanical and electrical connections can be freely selected.
- High measurement accuracy
- Very good media resistance
- Excellent corrosion resistance to aggressive media
- Resistance to excess and negative pressure
- High bursting strength
- Good thermal stability
- Excellent long-term stability
- Vibration resistance
- Low installation height
- Electromagnetic compatibility
- Very good price-performance ratio
Linear Sensors
- Our linear sensors and position encoders can be used wherever a linear position needs to be determined: in a device, system, drive, actuator, vehicle or machine.
Our portfolio is extremely varied, ranging from potentiometer elements to potentiometers, all the way through to membrane sensors in the most diverse range of designs, shapes, dimensions and lengths: from the delicate miniature sensor in the needle bed adapter to the 50-cm-long linear drive. It is even possible to integrate individual sensors and switches into a single component with our technology.
We offer a comprehensive range of standard products and develop tailor-made, individual and OEM solutions to suit your exact requirements and installation conditions. Potentiometric Position Sensor
Conductive plastic potentiometer WPL-OS
-
The WPL-OS position encoder with conductive plastic technology designed for absolute measurements consists of an open aluminium housing without connecting rod. It is characterised by a low installation height of 5.5 mm, easy integration and simple assembly. The electrical measuring range can be individually adjusted between 30 mm and 300 mm.
Advantages
- High resolution, precision and measurement accuracy
- Linearity of up to ± 0.25%
- Low wear, long service life of up to 10 million cycles
- Excellent long-term stability
- High thermal stability
- ESD- and EMC-compatible
- Simple assembly
- Robust design
- Very good price-performance ratio
Conductive plastic potentiometer WPL-LH
-
The WPL position transducer with conductive plastic technology designed for absolute measurements consists of an aluminium housing with steel connecting rod. Four different housing versions enable optimal mounting for every application.
It is characterised by compact dimensions, easy integration and simple assembly. It is available with various mechanical couplings. The electrical measuring range can be individually adjusted between 25 mm and 300 mm.
Advantages
- High resolution, precision and measurement accuracy
- Linearity of up to ± 2%
- Low wear, long service life of up to 5 million cycles
- Excellent long-term stability
- High thermal stability
- Protected against environmental influences up to IP 63
- ESD- and EMC-compatible
- Simple assembly
- Robust design
- Very good price-performance ratio
Linear Membrane Sensor
Linear membrane sensor MTP-L
-
This low-wear membrane sensor designed for analogue and absolute measurements is characterised by a good resolution and is hermetically sealed. Tapping takes place by means of a spring-loaded pin. It is easy to integrate thanks to its flat design measuring under 1mm. It is easy to attach thanks to an adhesive film that is affixed to the back. The electrical measuring range can be individually adjusted between 50 mm and 500 mm.
Advantages
- Particularly flat design measuring under 1 mm
- Good resolution, precision and measurement accuracy
- Linearity of ± 2%
- Low wear, long service life of up to 5 million cycles
- Excellent long-term stability
- ESD- and EMC-compatible
- IP 65 degree of protection
- Robust design
- Ideal for battery-powered applications
- Very good price-performance ratio
Membrane Sensor Positions Sensor linear MTP-LX
-
This low-wear membrane sensor designed for analogue and absolute measurements is characterised by a very good resolution, a long service life and very good linearity of up to < ± 0.3%. It can be used in a temperature range of up to 105 °C. Tapping takes place by means of a spring-loaded spring-loaded pin. It is hermetically sealed and impresses with its high degree of protection (IP 67) and its insensitivity to dust, dirt and liquid. A further advantage: the flat design measuring under 3 mm. The electrical measuring range can be individually adjusted between 30 mm and 500 mm.
Advantages
- Particularly flat design measuring under 3 mm
- Good resolution, precision and measurement accuracy
- Linearity of up to ± 0.3%
- Low wear, long service life of up to 5 million cycles
- Excellent long-term stability
- ESD- and EMC-compatible
- IP 67 degree of protection
- Robust design
- Ideal for battery-powered applications
- Very good price-performance ratio
Contactless, linear membrane sensor MMP
-
This wear-free membrane sensor designed for absolute measurements measures without contact and is hermetically sealed. It is characterised by a particularly flat design measuring under 2 mm. It is easy to attach thanks to an adhesive film that is affixed to the back. Tapping takes place without contact with a magnet at a distance from the sensor. The electrical measuring range can be individually adjusted between 50 mm and 500 mm.
Advantages
- Particularly flat design measuring under 2 mm
- Wear-free, long service life of up to 50 million cycles
- Excellent long-term stability
- IP 65 degree of protection
- Good resolution, precision and measurement accuracy
- Linearity of ± 2%
- ESD- and EMC-compatible
- Robust design
- Very low current consumption
- Ideal for battery-powered applications
- Good price-performance ratio
Potentiometer elements
Linear potentiometer elements
-
Our conductive plastic potentiometer elements designed for analogue and absolute measurements can be individually adapted to your specific requirements. The electrical measuring range can lie between 20 mm and 500 mm. The standard base material is FR4 although the products are also available in other materials. The contact technology is a wiper. The products can be used in a temperature range of -40 °C to +125 °C.
Tell us the desired dimensions and resistance value as well as your mechanical and electrical requirements and we will produce exactly the right sensor element according to your specifications. It is possible to integrate individual sensors and switches into a single component.
Advantages
- High resolution, precision and measurement accuracy
- Linearity of up to ± 0.1%
- Low wear, long service life of up to 50 million cycles
- Excellent long-term stability
- High thermal stability
- ESD- and EMC-compatible
- Simple assembly
- Robust, fail-safe design
- Very low current consumption
- Ideal for battery-powered applications
- Very good price-performance ratio
Rotary Sensors with Hall Effect
- Our conductive plastic and Hall rotary sensors and encoders are used wherever an angular position needs to be determined: in a device, system, drive, actuator, vehicle or machine. From crash test dummies to robots and cobots – we find the right solution for every application.
Our portfolio is extremely varied, ranging from potentiometer elements to potentiometers, all the way through to membrane sensors in the most diverse range of designs, shapes and dimensions.
We also develop tailor-made, individual solutions to suit your exact requirements and installation conditions. Potentiometer elements
- Our potentiometer elements are tailored to your exact requirements. Tell us the desired diameter, angle of rotation, resistance value as well as the mechanical and electrical orientation and we will produce exactly the right sensor element according to your specifications.
Potentiometer element for recording angles
-
Our conductive plastic potentiometer elements that are designed for absolute and analogue measurements are available in diameters of approx. 9 mm to 340 mm and with angles of rotation of 25° to 355°. The base material is FR4 although the products are also available in other materials and can be used in a temperature range of -40 °C to +125 °C. The contact technology is a wiper.
The products can be individually adapted to your specific requirements. Tell us the desired diameter, angle of rotation and resistance value as well as your mechanical and electrical requirements and we will produce exactly the right sensor element according to your specifications.
It is possible to integrate individual sensors and switches into a single component.- High resolution, precision and measurement accuracy
- Linearity of up to ± 0.1%
- Low wear, long service life of up to 50 million cycles
- Excellent long-term stability
- High thermal stability
- ESD- and EMC-compatible
- Simple assembly
- Robust, fail-safe design
- Ideal for battery-powered applications
- Very good price-performance ratio
Integrated rotary sensor
-
Our conductive plastic potentiometer elements are designed for absolute and analogue measurements and are ideal for use in highly integrated assemblies in which the signal coming from the potentiometer element is processed directly on the same circuit board. This high level of integration significantly reduces the number of components and the space required. The products can be used in the temperature range from -40° to 125°C. The contact technology is a wiper.
The products can be individually adapted to your specific requirements. Tell us the desired values as well as your mechanical and electrical requirements and we will produce exactly the right sensor element according to your specifications.
- Low wear, long service life of up to 50 million cycles
- Excellent long-term stability
- High thermal stability
- ESD- and EMC-compatible
- Simple assembly
- Robust, fail-safe design
- Ideal for battery-powered applications
- Very good price-performance ratio
Potentiometers rotary
Hall potentiometer POH 120
-
With a diameter of just 13 mm, this contactless rotary sensor based on Hall technology and designed for absolute measurements is particularly small. The angle of rotation can be freely programmed between 0 and 360°.
The housing is made from stainless steel with a servo flange for precise assembly. Advantages of the decoupled axle without bearings: compensation of play and tolerances and no bearing wear.Advantages
- Compact design with a housing diameter of 13 mm
- High resolution, precision and measurement accuracy
- Linearity of up to ± 0.5%
- Low wear, long service life of up to 200 million cycles
- Excellent long-term stability
- High thermal stability
- ESD- and EMC-compatible
- Degree of protection IP 67, decoupled without load
- Simple assembly
- Robust design
- Very good price-performance ratio
Hall-Potentiometer POH 120 with axle
-
With a diameter of just 13 mm, this contactless rotary sensor based on Hall technology and designed for absolute measurements is particularly small. The angle of rotation can be freely programmed between 0° and 360°.
The housing is made from stainless steel with a servo flange for precise assembly. The axle is made from nickel-plated brass and mounted on sliding bearings.Advantages
- Compact design with a housing diameter of 13 mm
- High resolution, precision and measurement accuracy
- Linearity of up to ± 0.5%
- Low wear, long service life of up to 200 million cycles
- Excellent long-term stability
- High thermal stability
- ESD- and EMC-compatible
- Degree of protection IP 65
- Simple assembly
- Robust design
- Very good price-performance ratio
Hall potentiometer HMS 220
-
This contactless rotary sensor designed for absolute measurements is based on Hall technology. The angle of rotation can be freely programmed between 0 and 360°. The stainless steel axle is mounted on ball bearings. The robust housing is made from aluminium. The output signal is analogue as standard, but also available as an SPI signal.
Advantages
- Housing diameter of 22.22 mm
- Ball bearings
- Sliding bearings on request
- High resolution of 12 bits
- Good linearity of up to ± 0.5 %
- Low wear, long service life of up to 200 million cycles
- Analogue or SPI output signal
- Excellent long-term stability
- High thermal stability
- ESD- and EMC-compatible
- Simple assembly
- Robust design
Conductive plastic hollow shaft potentiometer HWL 60
-
The hollow shaft potentiometer in conductive plastic designed for analogue measurements consists of a plastic housing and impresses with its simple design, variable connections and rotation lock and mounting orientation.
The D-shaped hollow shaft guarantees a good form fit with the rotation axis. The angle of rotation is 320° and this can be individually adjusted. Redundant versions are possible.Advantages
- High resolution, precision and measurement accuracy
- Linearity of up to ± 2%
- Low wear, long service life of up to 3 million cycles
- Excellent long-term stability
- Good thermal stability
- ESD- and EMC-compatible
- Simple assembly
- Hollow shaft design
- IP 50 degree of protection
- Ideal for battery-powered applications
- Very good price-performance ratio
Conductive plastic hollow shaft potentiometer PGL 60
-
The hollow shaft potentiometer in conductive plastic designed for analogue measurements consists of a non-rotating aluminium housing and a ball-bearing-mounted hollow shaft. The angle of rotation is 320° and this can be individually adjusted. The PGL 60 is characterised by high robustness, good linearity, excellent resolution and repeat accuracy.
Advantages
- High resolution, precision and measurement accuracy
- Linearity of up to ± 2%
- Ball-bearing-mounted hollow shaft
- Low wear, long service life of up to 25 million cycles
- Excellent long-term stability
- High thermal stability
- ESD- and EMC-compatible
- Simple assembly
- Robust design
- Aluminium housing
- IP 63 degree of protection
- Ideal for battery-powered applications
- Very good price-performance ratio
Conductive plastic potentiometer POL 120
-
With a diameter of just 13 mm, this rotary sensor in conductive plastic designed for analogue measurements is particularly small. The angle of rotation is 308° and this can be individually adjusted. The housing is made from brass with a servo flange for precise assembly. The axle is made from steel and mounted on sliding bearings.
Advantages
- Very small housing diameter of just 13 mm
- High resolution, precision and measurement accuracy
- Linearity of up to ± 2.5%
- Low wear, long service life of up to 3 million cycles
- Excellent long-term stability
- High thermal stability
- ESD- and EMC-compatible
- Simple assembly
- Robust design
- Very good price-performance ratio
- Ideal for battery-powered applications
Conductive plastic potentiometer POL 220
-
This rotary sensor in conductive plastic designed for analogue measurements is a precision potentiometer that is characterised by a long service life and good linearity. The angle of rotation is 320° and this can be individually adjusted. The robust aluminium housing has a diameter of 22.2 mm. The sliding-bearing-mounted axle is made from steel and has a diameter of 6.35 mm, optionally 3.15 mm. The standard connection consists of 3 litz wires. Solder pins are also possible.
Advantages
- Very high precision
- High resolution
- Linearity of up to ± 2%
- Low wear, long service life of up to 10 million cycles
- Excellent long-term stability
- High thermal stability
- ESD- and EMC-compatible
- IP 65 degree of protection
- Simple assembly
- Robust design
- Very good price-performance ratio
- Ideal for battery-powered applications
Conductive plastic potentiometer POL 200
-
This rotary sensor in conductive plastic designed for analogue measurements has a plastic housing with injected metal thread. The sliding bearing is integrated. The coordination of the materials between the axle and the sliding bearing guarantees a long service life. The angle of rotation is 320° and this can be individually adjusted.
Advantages
- High resolution, precision and measurement accuracy
- Linearity of up to ± 2%
- Low wear, long service life of up to 1 million cycles
- Excellent long-term stability
- High thermal stability
- ESD- and EMC-compatible
- Simple assembly
- Robust design
- IP 50 degree of protection
- Ideal for battery-powered applications
- Very good price-performance ratio
Conductive plastic potentiometer POL 230
-
This rotary sensor in conductive plastic designed for analogue measurements consists of a robust aluminium housing and a steel axle mounted on two ball bearings and is thereby designed for the highest mechanical loads. The axle diameter can be freely selected between 3 and 6.35 mm. A servo flange enables precise assembly. The cable, litz wire or PIN connection is tightly sealed. The angle of rotation is 340° and this can be individually adjusted. Redundant versions are possible.
Advantages
- High resolution, precision and measurement accuracy
- Linearity of up to ± 2%
- Ball-bearing-mounted axle
- Low wear, long service life of up to 20 million cycles
- Excellent long-term stability
- High thermal stability
- ESD- and EMC-compatible
- Simple assembly
- Robust design
- IP 63 degree of protection
- Ideal for battery-powered applications
- Very good price-performance ratio
Conductive plastic potentiometer POL 790
-
This rotary sensor in conductive plastic designed for analogue measurements is extremely robust, which makes it ideal for use in special vehicle manufacturing.
Good linearity, excellent resolution and repeat accuracy are further features of this potentiometer. The angle of rotation is 350° and this can be individually adjusted. The extremely robust housing is made from aluminium but is also available in a plastic version. The axle is made from stainless steel and is mounted on two sliding bearings. The shaft diameter measures 8 mm.Advantages
- Robust design
- High resolution, precision and measurement accuracy
- Linearity of up to ± 2%
- Low wear, long service life of up to 10 million cycles
- Excellent long-term stability
- High thermal stability
- ESD- and EMC-compatible
- Simple assembly
- IP 67 degree of protection
- Also suitable for battery-powered applications
- Very good price-performance ratio
High-voltage potentiometer POC 400
-
The high-voltage potentiometer POC 400 is based on a ceramic resistance carrier embedded in a well-insulating plastic housing. As a variable voltage divider, it offers ideal conditions for direct high-voltage regulation.
Our power spectrum
- Controllable high voltage up to 2,5 kV
- Resistance values 5 MO, 10 MO, 15 MO, 20 MO
- Tolerance ±10 %
- Linearity ± 4%
- Max. voltage up to bis 2,5 kV
Hall potentiometer POH 120
-
With a diameter of just 13 mm, this contactless rotary sensor based on Hall technology and designed for absolute measurements is particularly small. The angle of rotation can be freely programmed between 0 and 360°.
The housing is made from stainless steel with a servo flange for precise assembly. Advantages of the decoupled axle without bearings: compensation of play and tolerances and no bearing wear.Advantages
- Compact design with a housing diameter of 13 mm
- High resolution, precision and measurement accuracy
- Linearity of up to ± 0.5%
- Low wear, long service life of up to 200 million cycles
- Excellent long-term stability
- High thermal stability
- ESD- and EMC-compatible
- Degree of protection IP 67, decoupled without load
- Simple assembly
- Robust design
- Very good price-performance ratio
Hall-Potentiometer POH 120 with axle
-
With a diameter of just 13 mm, this contactless rotary sensor based on Hall technology and designed for absolute measurements is particularly small. The angle of rotation can be freely programmed between 0° and 360°.
The housing is made from stainless steel with a servo flange for precise assembly. The axle is made from nickel-plated brass and mounted on sliding bearings.Advantages
- Compact design with a housing diameter of 13 mm
- High resolution, precision and measurement accuracy
- Linearity of up to ± 0.5%
- Low wear, long service life of up to 200 million cycles
- Excellent long-term stability
- High thermal stability
- ESD- and EMC-compatible
- Degree of protection IP 65
- Simple assembly
- Robust design
- Very good price-performance ratio
Hall potentiometer HMS 220
-
This contactless rotary sensor designed for absolute measurements is based on Hall technology. The angle of rotation can be freely programmed between 0 and 360°. The stainless steel axle is mounted on ball bearings. The robust housing is made from aluminium. The output signal is analogue as standard, but also available as an SPI signal.
Advantages
- Housing diameter of 22.22 mm
- Ball bearings
- Sliding bearings on request
- High resolution of 12 bits
- Good linearity of up to ± 0.5 %
- Low wear, long service life of up to 200 million cycles
- Analogue or SPI output signal
- Excellent long-term stability
- High thermal stability
- ESD- and EMC-compatible
- Simple assembly
- Robust design
Membrane sensors
Membrane sensor MTP-R
-
This membrane sensor is designed for absolute and analogue measurements, is equipped with spring-loaded pin as contact technology, is available in various plastics and can be used in a temperature range of -25 °C to +85 °C.
The MTP-R is characterised by its particularly flat design, is hermetically sealed and is easy to attach with an adhesive film that can be affixed to the back on request. It is available in diameters of approx. 38 mm to 300 mm and with angles of rotation of 25° to 350° and can be individually adapted to your specific requirements.
Tell us the desired diameter, angle of rotation and resistance value as well as the mechanical and electrical requirements and we will produce exactly the right sensor element according to your specifications. It is possible to integrate individual sensors and switches into a single component.
Advantages:
- Particularly flat design measuring under 1 mm
- Good resolution, precision and measurement accuracy
- Linearity of up to ± 2%
- Low wear, long service life of up to 5 million cycles
- Excellent long-term stability
- ESD- and EMC-compatible
- Simple assembly, self-adhesive back
- IP 65 degree of protection
- Robust design
- Low current consumption
- Ideal for battery-powered applications
- Very good price-performance ratio
Membrane sensor MTP-RX
-
This membrane sensor is designed for absolute and analogue measurements and is equipped with spring-loaded pin as contact technology. It is available in various plastics and can be used in a temperature range of -25 °C to +105 °C.
The MTP-RX is characterised by its extremely flat design, is hermetically sealed and is easy to attach with an adhesive film that can be affixed to the back on request. It is available in diameters of approx. 38 mm to 340 mm and with angles of rotation of 25° to 350° and can be individually adapted to your specific requirements.
Tell us the desired diameter, angle of rotation and resistance value as well as the mechanical and electrical requirements and we will produce exactly the right sensor element according to your specifications. It is possible to integrate individual sensors and switches into a single component.
Advantages:
- Flat design measuring below 1 mm
- Good resolution, precision and measurement accuracy
- Linearity of up to ± 0.3%
- Low wear, long service life of up to 5 million cycles
- Ideal for battery-powered applications
- Excellent long-term stability
- ESD- and EMC-compatible
- Simple assembly, self-adhesive back
- IP 67 degree of protection
- Robust design
- Low current consumption
- Very good price-performance ratio
Membrane sensor MTP-integrated
-
Due to its flat design, the MTP-integrated can be placed directly on the evaluation electronics of a printed circuit board. This saves costs in logistics, production and service. It is hermetically sealed and, if desired, can be easily applied using an adhesive film attached to the back and is individually adapted to your respective requirements. It is available in various plastics and can be used in the temperature range from -25° to 85°C.
Tell us the desired diameter, angle of rotation and resistance value as well as the mechanical and electrical requirements and we will produce exactly the right sensor element according to your specifications.
The application example here shows one of the many possibilities.
Advantages:
- Low wear, long service life of up to 5 million cycles
- Particularly flat design measuring under 1 mm
- Good resolution, precision and measurement accuracy
- Excellent long-term stability
- ESD- and EMC-compatible
- Simple assembly, self-adhesive back
- IP 65 degree of protection
- Robust design
- Low current consumption
- Ideal for battery-powered applications
- Very good price-performance ratio
Joysticks
- Industrial joysticks are used in the most diverse range of applications. They are an important element in radio remote control as well as in the drive and function control of vehicles, construction machinery and boats, in materials handling and medical technology.
We have been developing high-quality thumb and finger joysticks for more than 35 years. We can develop a tailor-made solution to suit your exact application on the basis of our comprehensive, modular construction system.
All joysticks from Metallux are ergonomically shaped, highly precise, yet robust.
Their low weight, long service life and low current consumption support maximum productivity in construction, in all types of vehicle, in industry and in medical technology. Thumb joysticks
- Thumb joysticks are predominantly used in industrial wireless applications. Our joysticks are also used, however, to control machines, forklifts, mobile elevating work platforms and boats, and as control elements in wheelchairs and operating tables.
MJ-T10 thumb joystick
-
The MJ-T10 thumb joystick is one of the smallest industrial joysticks in the world.
Due to its small size and installation dimensions, it can be perfectly integrated into applications that require precise control but offer little space.
Its dimensions: total length approx. 25 mm, diameter approx. 18 mm, installation depth approx. 13 mmAdvantages
- Very small and compact
- Light weight
- 1 oder 2 axes
- Hall technology
- Redundant
- Deflection ±22,5°
- Gate shape: Round gate or Crossgate
- Up to IP 66 degree of protection
- Long service life
MJ-T11 thumb joystick
-
The redundant Hall joystick MJ-T11 is designed as a control element in joysticks, armrests and radio remote controls as well as for use in wheelchairs and off-highway vehicles.
Due to its small size and installation dimensions, it can be perfectly integrated into applications that require precise control but offer little space.
Advantages
- Small and compact
- Light weight
- 1 oder 2 axes
- Hall technology
- Redundant
- Deflection ±25,5°
- Gate shape: Round gate or Crossgate
- Up to IP 66 degree of protection
- Long service life
Finger joysticks
- Metallux finger joysticks can be used in the most diverse range of applications. They are ergonomically shaped, highly precise, yet robust – thereby guaranteeing the comfortable and safe operation of machines and devices. We have a comprehensive, modular construction system and use this as the basis for developing a tailor-made, individual solution to suit your exact application.
Joystick MJ-30 "Mammoth"
-
The MJ-H10 multiaxial hand joystick is designed for precise drive and function control. State-of-the-art technology, a robust construction and an ergonomic design make it the ideal control element for demanding functions.
Thanks to the special handle design, the control elements can be easily replaced on site. This saves time, reduces machine downtimes, increases machine availability and extends the already long service life.
Designs
- Hall or potentiometer technology
- Free choice of handle designs
- Base and handle available separately
- Freely configurable thumb plate
- Control elements can be replaced on site
- Numerous like CANOpen and SAE
- Switching path limitation
- Position detent
- Friction Brake
- Deadman function
MJ-F12 Finger-Joystick
-
The compact and robust MJ-F12 series with potentiometer technology guarantees precise control and a very low current consumption.
Thanks to our flexible modular system, the joystick can be designed in a range of variants, including position detents, potentiometer in the Z-axis, deadman function and various electrical signal variants.
The MJ-F12 and MJ-F13 series differ in the shape of the flange.
MJ-F12 (prev. MJ-2K): square
MJ-F13 (prev. MJ-3K): round
MJ-F13 finger joystick
-
This compact and robust industrial joystick with potentiometer technology is characterised by precise control and a very low current consumption. Its low weight and long service life support a high level of productivity in all applications.
Thanks to our flexible modular system, the joystick can be designed in a range of variants, including position detents, potentiometer in the Z-axis, deadman function and various electrical signal variants.
The MJ-F12 and MJ-F13 series differ in the shape of the flange.
MJ-F12 (prev. MJ-2K): square
MJ-F13 (prev. MJ-3K): round
MJ-F11 finger joystick
-
This 1-axis, analogue joystick is extremely light and robust. Thanks to potentiometer technology, it has a very low current consumption and is perfect for battery-powered applications such as radio remote control. Its compact housing and low installation depth enable space-saving installation.
Also available in Hall technology and with additional protective cap.
- Robust, compact design
- Low weight of approx. 35 g
- Small installation dimensions
- Temperature range of -25 °C to +70 °C
- Continuous brake, position detent in the zero position
- Up to IP 66 degree of protection
- Long service life of up to 5 million cycles
- Minimal current consumption
- Ideal for battery-powered applications
MJ-F14 finger joystick
-
This 2-axis joystick is equipped with wear-free Hall technology, making it suitable for environments with high vibrations.
Due to its low installation depth, it can be optimally used in applications with limited installation space.
It is available with open and closed rubber sleeve.
Features
- Robust design that can withstand vibrations
- Low installation depth
- Angular flange
- Long service life of up to 5 million cycles
- Can be installed from above
- Low weight
- IP 65 degree of protection
- analoger Output, optional redundant
- Präzise Nullpunktrückstellung
High Voltage Resistors
- Passive components like High-voltage resistors respectively High ohmic resistors are an absolute must in all applications involving high voltage in order to safely perform measurement, switching and control processes. Thick-film high-voltage resistors are ideal for this thanks to their wide range of designs, long service life and stability.
Our portfolio is very diverse. The products are available in various designs as flat and tubular high-voltage resistors. We also offer different series: Our range includes HV resistors, impulse resistors and high-voltage dividers as well as high-voltage networks, resistors for PCB assembly and adjustable high-voltage potentiometers. High Voltage Resistors
Flat high-voltage resistor 967 HVR
-
This flat, ceramic-based high-voltage resistor perfectly meets all requirements for low-induction, stable and robust passive components.
It is characterised by its excellent long-term stability and performance.
Our power spectrum
- Voltage in the open air of 5 to 45 kV
- Voltage in oil of 7.5 to 70 kV
- Output of 1 to 10 watts
- Resistance values of 100 kΩ to 30 GΩ
- Tolerances of up to ≥ 0.1%
- Voltage coefficient of up to 5 ppm/V
- Temperature coefficient from ≥ 10 ppm/°C
Protective covers made from epoxy, glass and silicone cement are available. Suitable for applications in the open air, SF6, in insulating oils and cast resin.
Available connection: Connection wire
This product is available in a wide range of versions. Alternatively, tell us the desired output, dimensions, resistance value and connection type and we will construct the appropriate resistor element.
Tubular high-voltage resistor 968 HVR
-
This tubular, ceramic-based high-voltage resistor perfectly meets all requirements for low-induction, stable and robust passive components.
It is characterised by its excellent long-term stability and performance.
Our power spectrum
- Voltage in the open air of 9 to 54 kV
- Voltage in oil of 13 to 81 kV
- Output of 3.8 to 20 watts
- Resistance values of 2 kΩ to 10 GΩ
- Tolerances of up to ≥ 0.1%
- Voltage coefficient of up to 16 ppm/V
- Temperature coefficient from ≥ 10 ppm/°C
Protective covers made from epoxy, glass and silicone cement are available. Suitable for applications in the open air, SF6, in insulating oils and cast resin.
Available connections: wired caps and caps with internal thread
This product is available in a wide range of versions. Alternatively, tell us the desired output, dimensions and resistance value and we will construct the appropriate resistor element.
Tubular high-voltage resistor 969 HVR
-
This tubular, ceramic-based high-voltage resistor perfectly meets all requirements for low-induction, stable and robust passive components.
It is characterised by its excellent long-term stability and performance.
Our power spectrum
- Voltage in the open air of 24 to 96 kV
- Voltage in oil of 32 to 148 kV
- Output of 11 to 105 watts
- Resistance values of 2 kΩ to 10 GΩ
- Tolerances of up to ≥ 0.1%
- Voltage coefficient of up to 15 ppm/V
- Temperature coefficient from ≥ 10 ppm/°C
Protective covers made from epoxy, glass and silicone cement are available. Suitable for applications in the open air, SF6, in insulating oils and cast resin.
Available connection: caps with internal thread
This product is available in a wide range of versions. Alternatively, tell us the desired output, dimensions and resistance value and we will construct the appropriate resistor element.
Flat high-voltage resistor 967 HPR
-
This flat, ceramic-based high-voltage resistor perfectly meets all requirements for precise, low-induction, passive components.
It is characterised by its extremely high accuracy.
Our power spectrum- Voltage in the open air of 5 to 45 kV
- Voltage in oil of 7.5 to 70 kV
- Output of 1 to 8 watts
- Resistance values of 200 kΩ to 30 GΩ
- Tolerances of up to ≥ 0.1%
- Voltage coefficient of up to 0.08 ppm/V
- Temperature coefficient from ≥15 ppm/°C
Protective covers made from epoxy, glass and silicone cement are available. Suitable for applications in the open air, SF6, in insulating oils and cast resin.
Available connection: connection wire
This product is available in a wide range of versions. Alternatively, tell us the desired output, dimensions, resistance value and connection type and we will construct the appropriate resistor element.
High Voltage Precision Resistors HPR 968
-
This tubular, ceramic-based high-voltage resistor perfectly meets all requirements for precise, low-induction, passive components.
It is characterised by its extremely high accuracy.
Our power spectrum
- Voltage in the open air of 9 to 54 kV
- Voltage in oil of 13 to 81 kV
- Output of 6 to 12 watts
- Resistance values of 2 kΩ to 10 GΩ
- Tolerances of up to ≥ 0.1%
- Voltage coefficient of up to 0.08 ppm/V
- Temperature coefficient from ≥ 15 ppm/°C
Protective covers made from epoxy, glass and silicone cement are available. Suitable for applications in the open air, SF6, in insulating oils and cast resin.
Available connections: wired caps and caps with internal thread
This product is available in a wide range of versions. Alternatively, tell us the desired output, dimensions and resistance value and we will construct the appropriate resistor element.
Tubular high-voltage resistor 969 HPR
-
This tubular, ceramic-based high-voltage resistor perfectly meets all requirements for precise, low-induction, passive components.
It is characterised by its extremely high accuracy.
Our power spectrum
- Voltage in the open air of 24 to 96 kV
- Voltage in oil of 32 to 148 kV
- Output of 7 to 75 watts
- Resistance values of 2 kΩ to 10 GΩ
- Tolerances of up to ≥ 0.1%
- Voltage coefficient of up to 0.1 ppm/V
- Temperature coefficient from ≥ 100 ppm/°C
Protective covers made from epoxy, glass and silicone cement are available. Suitable for applications in the open air, SF6, in insulating oils and cast resin.
Available connection: caps with internal thread
This product is available in a wide range of versions. Alternatively, tell us the desired output, dimensions and resistance value and we will construct the appropriate resistor element.
High-voltage divider 967 HVD
-
This flat, ceramic-based high-voltage divider consists of two individually adjustable resistors and perfectly meets all requirements for low-induction, stable and robust passive components.
Our power spectrum- Voltage in the open air of 5 to 32 kV
- Voltage in oil of 7.5 to 49 kV
- Output of 5 to 2.4 watts
- Resistance values of 5 MΩ to 2 GΩ
- Absolute tolerances of ≥ 0.5%
- Tolerance ratio of ≥ 0.1%
- Voltage coefficient of up to 0.2 ppm/V
- Absolute temperature coefficient from ≥ 25 ppm/°C
- Temperature coefficient ratio from ≥ 15 ppm/°C
Flat high-voltage resistor on plastic carrier
-
This resistor is printed onto carrier materials such as flexible films or plastic.
The advantage: the resistor can be designed in a variety of shapes, thereby opening up significantly more options in terms of construction design.Our power spectrum:
- Voltage in the open air of up to 40 kV
- Output of up to 1 watt
- Resistance values of 2 kΩ to 100 MΩ
- Tolerances of 30%
The connection can be individually designed.
Tell us the desired dimensions and resistance value as well as your mechanical and electrical requirements and we will produce exactly the right resistor element according to your specifications. Individual integration into existing assemblies is also possible.
High-voltage potentiometer POC 400
-
The high-voltage potentiometer POC 400 is based on a ceramic resistance carrier embedded in a well-insulating plastic housing. As a variable voltage divider, it offers ideal conditions for direct high-voltage regulation.
- Our power spectrum Controllable high voltage up to 2,5 kV
- Resistance values 5 MO, 10 MO, 15 MO, 20 MO
- Tolerance ±10 %
- Linearity ± 4%
- Max. voltage up to bis 2,5 kV
High-voltage network 967 HNW
- This ceramic-based high-voltage network consists of more than two individual resistors per substrate and is adapted to your individual requirements.
Flat high-voltage resistor 967 HVS SMD-compatible
-
This flat, ceramic-based high-voltage resistor is designed for PCB assembly. It perfectly meets all requirements for low-induction, stable, passive components.
It is characterised by its excellent long-term stability and performance.
Our power spectrum
- Voltage in the open air of 5 to 45 kV
- Voltage in oil of 7.5 to 70 kV
- Output of 1 to 10 watts
- Resistance values of 100 kΩ to 30 GΩ
- Tolerances of up to ≥ 0.1%
- Voltage coefficient of up to 5 ppm/V
- Temperature coefficient from ≥ 10 ppm/°C
Power Resistors
- Our portfolio comprises two different technologies: power resistors with thick-film technology and wire resistors – the optimum solution for every application.
A thick-film power resistor is characterised by an extremely low construction height combined with excellent stability. Our portfolio includes standard products as well as custom solutions.
Wire resistors are robust and ideal for high, constant or cyclical loads. We offer a comprehensive selection of different designs and options. 
PLR power film resistor
-
With its compact design, the PLR offers a high power density in a confined space. It differs from classically wound wire tube resistors in its significantly lower inductance and significantly higher resistance values of up to 650 Ω.
The standard versions are the PLR 100 with 100 watts, the PLR 200 with 200 watts and the PLR 300 with 300 watts.
Due to its high temperature resistance, the PLR is based on a steel substrate, which also makes it resistant to temperature shocks and mechanical loads. Depending on the application, ceramic can also be used as the base material.
The electrical connection is established via standard litz wires, blade terminal or soldering eyelet.
This product is available in a wide range of versions. Tell us your desired output, dimensions and resistance value and we will produce the right resistor element to suit your requirements.
- Low inductance of < 6 µH
- Resistance values of 5 Ω to 650 Ω
- Tolerance of ±10%
- Operating voltage of up to 1000 VDC
- Simple assembly
- Compact, robust design
- Standard: steel substrate
PWR-S with aluminium housing
-
This wire resistor with an aluminium profile combines the high pulse stability of tried-and-tested wire materials with optimised thermal conduction and a high degree of protection. Mounting on a thermally conductive surface further improves heat dissipation and increases stability. The products PWR-S 100 - 150 satisfies the requirements of UL 508.
Connection lines available in various lengths and materials. Optionally available with integrated temperature switch. Also available as a customer-specific assembly on request.
This product is available in a wide range of versions. Tell us your desired output, dimensions and resistance value and we will produce the right resistor element to suit your requirements.
- Freely selectable resistance value
- Output of up to 150 watts
- High pulse stability
- High degree of protection IP 55
- Simple assembly
- Low space requirement
- UL 508 approval (PWR-S 100 - 150)
PWR-R with aluminium housing
-
This wire resistor with an aluminium profile combines the high pulse stability of tried-and-tested wire materials with optimised thermal conduction and a high degree of protection. Mounting on a thermally conductive surface further improves heat dissipation and increases stability. The product satisfies the requirements of UL 508.
Connection lines available in various lengths and materials. Optionally available with integrated temperature switch. Also available as a customer-specific assembly on request.
This product is available in a wide range of versions. Tell us your desired output, dimensions and resistance value and we will produce the right resistor element to suit your requirements.
- Freely selectable resistance value
- Output of up to 600 watts
- High pulse stability
- High degree of protection (IP 55)
- Simple assembly
- Low space requirement
- UL 508 approval
PWR-O with aluminium housing
-
This wire resistor with an aluminium profile combines the high pulse stability of tried-and-tested wire materials with optimised thermal conduction and a high degree of protection. Mounting on a thermally conductive surface further improves heat dissipation and increases stability. The product satisfies the requirements of UL 508.
Connection lines available in various lengths and materials. Optionally available with integrated temperature switch. Also available as a customer-specific assembly on request.
This product is available in a wide range of versions. Tell us your desired output, dimensions and resistance value and we will produce the right resistor element to suit your requirements.
- Freely selectable resistance value
- Output of up to 600 watts
- High pulse stability
- High degree of protection (IP 55)
- Simple assembly
- Low space requirement
- UL 508 approval
PWR-F with aluminium housing
-
This wire resistor with an aluminium profile combines the high pulse stability of tried-and-tested wire materials with optimised thermal conduction and a high degree of protection. Mounting on a thermally conductive surface further improves heat dissipation and increases stability. The resistors PWR-F 150 to 600 satisfie the requirements of UL 508.
Connection lines available in various lengths and materials. Optionally available with integrated temperature switch. Also available as a customer-specific assembly on request.
This product is available in a wide range of versions. Tell us your desired output, dimensions and resistance value and we will produce the right resistor element to suit your requirements.
- Freely selectable resistance value
- Output of up to 1,000 watts
- High pulse stability
- High degree of protection (IP 55)
- Simple assembly
- Low space requirement
- UL 508 approval (PWR-F 150 to 600)
PWR-TR 2XX power wire resistor
-
The PWR-TR is a cemented wire tube resistor. It utilises the full carrying capacity of the resistor material, as the heat that is generated can be dissipated into the environment via the shortest route.
We offer connection and assembly materials as well as the PWR-TRR with additional tap clamps for adjusting the resistance values.
This product is available in a wide range of versions. Tell us your desired output, dimensions and resistance value and we will produce the right resistor element to suit your requirements.
- Freely selectable resistance value
- High pulse stability
- Output of up to 100 watts
- IP 00 degree of protection
- Simple assembly
- Low space requirement
- Tube diameters of 17 and 24 mm
- Available in various lengths
PWR-TR 3XX power wire resistor
-
The PWR-TR is a cemented wire tube resistor. It utilises the full carrying capacity of the resistor material, as the heat that is generated can be dissipated into the environment via the shortest route.
We offer connection and assembly materials as well as the PWR-TRR with additional tap clamps for adjusting the resistance values.
This product is available in a wide range of versions. Tell us your desired output, dimensions and resistance value and we will produce the right resistor element to suit your requirements.
- Freely selectable resistance value
- High pulse stability
- Output of up to 1300 watts
- IP 00 degree of protection
- Simple assembly
- Low space requirement
- Tube diameters of 35, 47 and 68 mm
- Available in various lengths
PWR-H with aluminium housing
-
This wire resistor with an aluminium profile combines the high pulse stability of tried-and-tested wire materials with optimised thermal conduction and a high degree of protection. Mounting on a thermally conductive surface further improves heat dissipation and increases stability.
Connection lines available in various lengths and materials. Optionally available with integrated temperature switch. Also available as a customer-specific assembly on request.
This product is available in a wide range of versions. Tell us your desired output, dimensions and resistance value and we will produce the right resistor element to suit your requirements.
- Freely selectable resistance value
- Output of up to 240 watts
- High pulse stability
- High degree of protection (IP 55)
- Simple assembly
- Low space requirement
PWR-X power wire resistor
-
The PWR-X is a ready-for-installation assembly consisting of several cemented wire tube resistors. Six different housing sizes are available for selection, for outputs ranging from 400 to 6,000 watts.
The series is characterised by a high degree of flexibility and can be used in numerous individual solutions. We offer a matching temperature switch for every power class.
- Ready-for-installation assembly
- Housing made from sheet steel
- Six different housing sizes
- Outputs from 400 to 6,000 watts
- Robust
- Pulse-resistant
- Individual pre-connection possible
