• Offer Profile
  • Since 1956 Salami Spa has been producing and selling hydraulic components.

    Today, more than 50 years of experience allow the company to present the most complete range of products aimed to the customer’s satisfaction. Salami Spa works for the customer and with the customer.
Product Portfolio

  • Gear Pumps and Motors with Aluminum Alloy Body

    • GROUP 1, 1.6 - E SERIES

    • - Gear pumps and motors made with aluminum alloy body, flanges and rear covers
      - Displacements from 0,9 cm3/giro (0,05 cu.in./rev.) to 6,5 cm3/giro (0,39 cu.in./rev.)
      - All pumps and motors are tested after assembly and run-in to ensure the high standard
      required by Salami engineers.

    • GROUP 2 - E SERIES

    • - Gear pumps made with aluminum alloy body and cast iron flanges and rear covers.
      - Displacements from 3,2 cm3/rev (0,19 cu.in./rev.) to 26 cm3/rev (1,58 cu.in./rev.)
      - Extremely compact design on the multiple assembling pump for the 2PE type.
      - All pumps and motors are tested after assembly and run-in to ensure the high standard required by
      Salami engineers.

    • GROUP 2.5 - B SERIES

    • - Gear pumps made with aluminum alloy body and cast iron flanges and rear covers.
      - Displacements from 3,2 cm3/rev (0,19 cu.in./rev.) to 26 cm3/rev (1,58 cu.in./rev.)
      - Extremely compact design on the multiple assembling pump for the 2PE type.
      - Assembling on multiple stage pump also available in combination with 2PE or 1.5PB types.
      - All pumps and motors are tested after assembly and run-in to ensure the high standard required by
      Salami engineers.

    • GROUP 3 - B SERIES

    • - Gear pumps and motors made with aluminum alloy body, flanges and rear covers.
      - Displacements from 21 cm3/rev (1.26 cu.in./rev.) to 75 cm3/rev (4.48 cu.in./rev.)
      - Assembling on multiple stage pump 3PB/3PB available.
      - Assembling on multiple stage pump also available in combination with 2PE type.
      - All pumps and motors are tested after assembly and run-in to ensure the high standard required by Salami engineers.

    • GROUP 3.5 - B SERIES

    • - Gear pumps and motors made with aluminum alloy body, flanges and rear covers.
      - Displacements from 55 cm3/giro (3,34 cu.in./rev.) to 98 cm3/giro (6,03 cu.in./rev.)
      - Assembling on multiple stage pump 3,5PB/3,5PB available.
      - Assembling on multiple stage pump also available in combination with 2PE, 2PB or 3PB types.
      - All pumps and motors are tested after assembly and run-in to ensure the high standard required by Salami engineers.

  • Gear Motors with Aluminum Alloy Body

      • GROUP 2 - E SERIES

      • - Gear motors made with aluminum alloy body and cast iron flanges and rear covers.
        - Displacements from 4.5 cm3/rev (0,27 cu.in./rev.) to 26 cm3/rev (1,58 cu.in./rev.).
        - Rated pressure up to 250 bar (3630 psi) -
        - Back pressure capability up to 120 bar (1740 psi) only in by-directional release.
        - All motors are tested after assembly and run-in to ensure the high standard required by
        Salami engineers.

  • Gear Flow Divider with Aluminum Alloy Body

      • GROUP 2 - E SERIES

      • - Gear flow dividers made with alluminium alloy body and cast iron end covers.
        - Displacements from 3,2 cm3/rev (0,19 cu.in./rev.) to 30 cm3/rev (1,83 cu.in./rev.)
        - Extremely compact design.
        - Available also with main relief valves to realign the cylinders at the end of stroke.
        - All flow dividers are tested after assembly and run-in to ensure the high standard required by
        Salami engineers.

  • Gear Pumps, Motors and Flow Dividers with Cast Iron Body

      • GROUP 3 - H SERIES

      • - Gear pumps and motors made in spheroidal cast iron.
        - Displacements from 21 cm3/rev (1.3 cu.in./rev) to 90 cm3 /rev (5.4 cu.in./rev).
        - Assembling on double stage pump 3HP/3HP available.
        - Assembling on multiple stage pump also available in combination with 2PB or 2.5PB types.
        - All pumps and motors are tested after assembly and run-in to ensure the high standard required
        by Salami engineers.

  • Directional Control Valves - Sectional Types

    • VD6A

    • - cast-iron made (inlet section, working section, outlet section) up to 8 working sections.
      - parallel circuit, load check valve protection on each section.
      - series circuit, load check valve protection on each section (possibility of 2nd load check valve on series line)
      - tandem circuit, load check valve protection on each section.
      - possibility of power beyond configuration and possibility of closed center.
      - several types of spool: double, single acting, spool motor, float position, regenerative position etc.
      - several spool control and spool positioning devices.
       

    • VD8A

    • - cast-iron made (inlet section, working section, outlet section) up to 8 working sections.
      - parallel circuit, load check valve protection on each section.
      - series circuit, load check valve protection on each section (possibility of 2nd load check valve on series line)
      - tandem circuit, load check valve protection on each section.
      - possibility of power beyond configuration and possibility of closed center.
      - several types of spool: double, single acting, spool motor, float position, regenerative position etc.
      - several spool control and spool positioning devices.

    • VD10A - VD12A

    • -cast-iron made (inlet module or inlet plus working module, single working module, outlet module).
      -parallel circuit, load check valve protection on each section.
      -series circuit, load check valve protection on each section. (series line realized inside of the spool with dedicated lcv)
      -tandem circuit, load check valve protection on each section.
      -possibility of power beyond configuration.
      -spool construction in steel, nickel plated to obtain a higher surface hardness and a better corrosion resistance.
      -several types of spool: double, single acting, spool motor, float position etc.
      -available spool with overcenter valve built-in, available spool with hydraulic kick-out built-in
      -minimum tolerance between the spools and the body to obtain a minimum internal leakage.
      -interchangeability of all the spools.
      -several spool positioning devices.

  • Directional Control Valves - Monoblock Types

    • VDM6

    • - cast-iron monoblock construction from 1 to 7 working sections.
      - parallel circuit, load check valve protection on down-stream of the pressure "P" line.
      - tandem circuit, only the first working section, l.c.v. protection + l.c.v. protection on down-stream of the "P" line.
      - possibility of power beyond.
      - several types of spool: double, single acting, spool motor, float position, regenerative position etc.
      - several spool control devices and spool positioning devices.

    • VDM6A

    • - cast-iron monoblock construction from 1 to 7 working sections.
      - parallel circuit, load check valve protection on each section.
      - possibility of power beyond configuration.
      - several types of spool: double, single acting, spool motor, float position, regenerative position etc.
      - possibility of auxiliary valve either on port A or B or on both.
      - several spool control devices and spool positioning devices.

    • VDM09

    • - cast-iron monoblock construction from 1 to 6 working sections.
      - parallel circuit, load check valve protection on down-stream of the pressure "P" line.
      - possibility of power beyond.
      - several types of spool: double, single acting, spool motor, float position, regenerative position etc.
      - several spool control devices and spool positioning devices.

    • VDM8

    • - cast-iron monoblock construction from 1 to 5 working sections.
      - parallel circuit, load check valve protection on each section.
      - possibility of power beyond configuration.
      - several types of spool: double, single acting, spool motor, float position, regenerative position etc.
      - possibility of auxiliary valve either on port A or B or on both.
      - several spool control devices and spool positioning devices.

  • Pressure Compensated Directional Control Valves

      • VDP08

      • - load sensing directional control valve.
        - made on cast-iron (inlet section, working section, end section).
        - available with inlet module for fixed or variable displacement pump.
        - inlet module with pressure compensator built-in, working modules with pressure compensator built-in..
        - several types of spool: double, single acting, spool motor, float position etc.
        - possibility of auxiliary valve either on port A or B or on both.
        - possibility of pressure relief valve on the LS line coming from the ports.