• Offer Profile
  • Sarspec is a technology leader in spectroscopy instrumentation. The products quality and expertise of our engineers and scientists grant the best support and concrete answers to requests from spectroscopy users around the world.
Product Portfolio
  • Pre- Configured Spectroscopy Solutions

      • Absorbance SPEC Pack

      • There are many ways to perform Absorbance measurements, either with the traditional cuvettes, probes that can be used in reaction vessels or flow cells. With Sarspec’s spectrometers the absorbance measurements can be made either with speeds up to 2857 spectra per second, optical resolutions better than 0.1 nm in a detection range from 180 to 1100 nm. The spectrometers used in these configurations have extra flexibility and robustness (with no moving parts) when compared with regular spectrophotometers and allow full spectra acquisition with time resolution down to 350 µsec - ideal when performing Absorbance vs. Wavelength vs. Time measurements.

        As full pack for Absorbance measurements all SPEC Packs are configured with wide range UV/Vis/NIR spectrometers, Light Source DW (Deuterium Tungsten) and different accessories depending on application. The available pre-configured solutions from Sarspec for Absorbance are:
          • Absorbance SPEC Pack CUV

          • The Absorbance Full Pack CUV is an affordable and flexible solution for using traditional cuvettes in Absorbance measurements.

            This configuration uses a SPEC RES+ UV/Vis/NIR spectrometer with 10 µm slit, granting an optical resolution of 0.75 nm and wavelength range of 200-1050 nm.

            The Light Source LS-DW is an high stability light source, emitting from 200-1100 nm with shutter and external or local control. The solution is complete with 600 µm core diameter Optical Fibers (50 cm length) and a Cuvette Holder for Absorbance with 6 mm Collimating Lens.
          • Absorbance SPEC Pack PROBE

          • The Absorbance SPEC Pack PROBE is quite useful when the user is unable to place the sample into a cuvette or use a flow cell. In situations where the reaction needs to be screened inside a vessel or reactor, the Absorbance SPEC Pack is the perfect solution.

            Includes a Spec RES+ UV/Vis/NIR with 10 µm slit for 0.75 nm optical resolution and wavelength range of 200-1050 nm, light source LS-DW with high stability and emission from 200 to 1100 nm and Transmission Probe with 600 µm core diameter.
          • Absorbance SPEC Pack FLOW

          • Flow measurements are one of the best cases to take advantage of the full spectrum vs. time acquisition available in all SPEC spectrometers when using the high flexibility of Kinetics Module from LightScan Software. This solution has been used in applications such as Flow Injection Analysis (FIA) and as an HPLC (High Pressure Liquid Chromatography) detector with great results and affordable price.

            The configuration uses a SPEC STD UV/Vis/NIR enhanced sensitivity with wavelength range from 200-1050 nm, 25 µm slit with an optical resolution of 1.7 nm and minimum integration time of 2 ms for fast sample screening. Together with the light source LS-DWHP emitting from 200 to 1100 nm, the Z format flow cell FCAPE / FCASS with 1 cm path length and optical fibers with 600 µm core diameter for maximum sensitivity.
             
        • Reflectance SPEC Pack

        • Reflectance works as an useful tool in materials analysis, color measurement, geology, food testing, etc.

          The general configuration consists of a SPEC STD spectrometer configured with 25 µm slit, light source, reflectance probe, probe holder and reflectance standard. LightScan software is also included in this package with a specific module for Reflectance measurements allowing Calibration, Multi-spectra, Quantification, etc. Reflectance measurements can be performed in time.
              • Reflectance SPEC Pack VIS/NIR

              • The standard configuration for the Reflectance SPEC Pack Vis comprises a SPEC STD Vis/NIR with 25 µm slit and 600 grooves/mm grating blazed at 750 nm with an optical resolution of 1.4 nm and a linear array CCD detector Sony 2048 pixels.

                The light source is the LS-W25 with tungsten lamp and wavelength range from 380 to 1100 nm. Also included is the Reflectance Probe, reflectance standard DRSTD98 and a probe holder that allows mesaurements of diffuse and specular reflectance.

                One typical application for this configuration is color measurement applied to a wide field of industrial areas like textiles, food, paints, ceramics, metals and polymers. Others applications include agriculture, defense and secutiy, remote sensing, solar power, thin film thickness, forensics, research, quality control, sorting and material characterization.
          • Flourescence SPEC Pack

          • When performing Fluorescence measurements, in most applications, sensitivity is a key factor and at Sarspec we take it seriously. The configurations offered takes the sensitivity to a new level by using back thinned detectors with quantum efficiency up to 78% and 1 mm height pixel elements combined with large 200 µm slits and collecting lens. This combination makes all the difference in the detection of fluorescence signal.

            Combining the detector with high power LEDs from LS-LED Light Source - with easily interchangeable LEDs - customers can have a sensitive and flexible solution for a fraction of the cost of a traditional spectrofluorimeter. For UV excitation we recommend the Xenon Flashlamp Light Source LS-XeF.
              • Flourescence SPEC Pack CUV

              • This is the most sensitive configuration available, mainly due to the sensitivity of the back thinned CCD array with high quantum efficiency (up to 78%) together with 200 µm slit, and collecting lens for the detector.

                Also, the high power LEDs from the flexible LS-LED Light Source - where many different excitation wavelengths can be used by simply changing the LED slide - contributes greatly for the final sensitivity. In this configuration the sample holder takes an important role on the sensitivity and flexibility of the solution. Sarspec’s Multipurpose Cuvette Holder uses 12.7 mm diameter lens for large sample area illumination/collection and reflecting mirrors to employ all radiation available and supports a wide range of filters easily interchangeable.
                 
              • Flourescence SPEC Pack CUV Basis

              • With great sensitivity in the Visible range, the SPEC PACK CUV BASIC is the most affordable solution for fluorescence available.

                Using a SPEC STD FL spectrometer with 200 µm slit and collecting lens for greater sensitivity, the LS-LED Light Source with high power LEDs and where due to the LED slide principle can easily change the excitation wavelength, large core optical fibers and the flexible cuvette holder CH.
              • Flourescence SPEC Pack XEF

              • When high power excitation in the UV is required the light source is normally quite expensive. An affordable solution for users that want to work with UV excitation and obtain good results in Fluorescence is to use the Xenon Flashlamp Light Source LS-XeF from Sarspec. With it, it's possible to obtain great fluorescence results with high flexibility.

                The full configuration includes the high sensitivity spectrometer SPEC SENSE+ UV/Vis with a back-thinned CCD array with 2048 elements and great quantum efficiency in the UV Range, optical fibers with 1000 um core diameter (50 cm), the multipurpose cuvette holder CH-MP with filter slots, large lens and signal enhancing mirrors (CH-MP-EM).
              • Flourescence SPEC Pack FLOW

              • In the Fluorescence SPEC PACK FLOW one can combine the flow analysis technique with fluorescence measurements making it a powerful tool for research in Biology and Chemistry.

                The configuration of this solution consists on the highly sensitive SPEC SENSE+ FL spectrometer using a back thinned CCD (Q.E. = 78%) with collecting lens and 200 µm slit. The LS-LED light source with high power LEDs (where due to the cassette principle can easily change the excitation wavelength) the Flow Cell FCFPE or FCFSS with sapphire windows and SMA connection completes this solution.
                 
            • Pre- Configured Spectroscopy Solutions

                • Ensina


                • • Absorbance, Transmittance and Kinetics
                  • Optional Fluorescence and External Upgrades
                  • Low Cost • Filter Slot for Slide Filters
                  • Aprox. 1 nm Optical Resolution
                  • Wavelength Range from 380 to 900nm
                  • Fast: up to 3ms per full spectrum
                  • Software Lightscan Ensina included
                  • Innovative RSpec - rotational selection of different techniques
                  • USB Powered - Portable when connected to a laptop

                  Sarspec's new ensina is a high performance, smart, robust, flexible, small and fast spectrophotometer built as an educational solution suitable for a wide range of experiments in different applications such as Absorbance, Transmittance, Kinetics. An optional Fluorescence upgrade offers unmatched flexibility with a large number of available LEDs and easy switch using a slide configuration. Ensina can also be upgraded with an External mode where through and optical fiber it is possible to use this spectrophotometer as a multichannel light detector.
                      • Ensina

                      • COMPLETE SOLUTION IN THE PALM OF YOUR HAND
                        • Absorbance
                        • Transmittance
                        • Kinetics
                        • Fluorescence
                        • External Connection
                        • Portable
                        • Optical Filters
                        • Affordable
                        • Fast

                        Extreme flexibility with a system suitable for liquid and solid samples. In the standard configuration you get a compact spectrophotometer with 22 (L) x 12 (D) x 6.5 (H) centimeters suitable for Absorbance, Transmittance and Kinetics measurements and software LightScan suitable for qualitative and quantitative analysis in the 380-1000nm (Visible and NIR) range. One filter slot is also available where slide filters can be used for a more specific wavelength range selection and/or educational purposes.

                        This solution can optionally be configured for Fluorescence where the same easy interchangeable LEDs principle as the LS-LED Light Source is used with a large number of slide LEDs available for different wavelengths.

                        In every spectrophotometer you are able to use an external port that can coupled to external light sources / spectrometers or just for external light detection. Use this port for Reflectance Measurements when using the optional Solid Sample Holder coupled to an LS-W Tungsten Halogen Light Source.

                  • Spectrometers

                      • SPEC STD

                      • • Detection from 180-1100 w/ 2048 pixels linear detector CCD array ​• Minimum integration time of 2 ms
                        ​• Triggering functions for easy integration (trigger in/out and delay) ​• Portable, fast and small size
                        ​• High speed mini USB 2.0 for power and control ​• Software LightScan included
                        ​• Also available as an OEM instrument ​• SMA 905 fiber connector, no optical alignment required
                        ​• Robust: fully built in aluminium ​• LED backlight indicator

                        When looking for an affordable and flexible spectrometer the SPEC STD range is the best option. With detection from 180 to 1100 nm, it can be used in Absorbance, Transmittance, Reflectance, Irradiance, Color and Fluorescence measurements.
                          • SPEC STD UV/VIS

                          • The SPEC STD UV/Vis is a flexible, multi application spectrometer for users that need to measure in the ultraviolet and visible regions. It’s suitable for a wide range of measurement techniques, including Absorbance, Transmittance, Reflectance and Irradiance.​

                            • Wavelength range: 180-880 nm
                            ​• Superior UV sensitivity
                            ​• Optical Resolution: 1.4 nm
                            ​• 600 grooves/mm grating blazed at 300 nm
                            ​• Order sorting filters included
                            ​• Optional Enhanced Sensitivity version

                            This standard configuration includes a 2048 pixels Sony CCD array detector, 25 µm slit which offers an excellent compromise between resolution and sensitivity, 600 grooves/mm grating blazed at 300 nm, order sorting filters, mini USB for communication and power the spectrometer and SMA 905 for Optical Fiber connection.
                          • SPEC STD UV/VIS/NIR

                          • Built specially for multi-application users, this model is a great solution for educational purposes and research on institutions with multi-users and multi-applications that need a robust instrument for fast sample screening. It’s suitable for a wide range of measurement techniques, including Absorbance, Transmittance, Reflectance, Irradiance, Color Measurement and many more.

                            • Wavelength range: 200-1050 nm
                            ​• Superior UV sensitivity
                            ​• Optical Resolution:1.7 nm
                            ​• 500 grooves/mm grating blazed at 300 nm
                            ​• Order sorting filters included
                            ​• Flexible and affordable full range spectrometer

                            The SPEC STD UV/Vis/NIR is a wide range spectrometer configured with a 500 grooves/mm grating blazed at 330 nm for great performance in all range. Includes also a 2048 pixels Sony CCD array detector, 25 µm slit, order sorting filter, mini USB 2.0 for communication and power the spectrometer and SMA 905 for optical fiber connection.
                             
                          • SPEC STD VIS/NIR

                          • The SPEC STD Vis/NIR is suitable for Absorbance, Transmittance, Reflectance, and Irradiance in its detection range.

                            • Wavelength range: 380-1050 nm
                            ​• Optical Resolution: 1.4 nm
                            ​• 600 grooves/mm grating blazed at 750 nm
                            ​• Order sorting filters included

                            Ranging from 380 to 1050 nm the SPEC STD Vis/NIR was designed with a 25 µm slit for good resolution and sensitivity, a 600 grooves/mm grating blazed at 750 nm for maximum efficiency on the NIR region and, as all STD spectrometers, includes a Sony 2048 pixels linear CCD array, order sorting filters, SMA connector for optical fibers and a Enhanced Sensitivity version as an option.
                          • SPEC STD FL

                          • The SPEC STD FL offers great sensitivity allowing detection of 19.3 pM of Eosin in low picoMolar concentration when configured with Sarspec's LED Light Source with LED-495nm, the multipurpose cuvette holder and 1000 µm optical fiber (2 units) - images below.

                            • Designed for Fluorescence measurements
                            ​• Wavelength range: 300-1000 nm
                            ​• 200 µm slit and collecting lens for maximum sensitivity
                            ​• 600 grooves/mm grating blazed at 500 nm
                            ​• Order sorting filters included
                            ​• Gain control up to 500 levels

                            The SPEC STD FL spectrometer was specially designed to be an affordable option for fluorescence measurements, including a 200 µm slit and collecting lens, as standard, for maximum sensitivity.

                            The detector uses the Sony 2048 pixels CCD Array with 200 µm pixel height. Also included, the SMA 905 connector for optical fiber and order sorting filter which removes higher order effects.
                             
                        • SPEC RES+

                        • ​• Detection from 180 to 1100 nm ​• High speed mini USB 2.0 for power and control
                          ​• 3648 pixels linear array CCD detector ​• Also available as an OEM instrument
                          ​• Great optical resolution of 0.2 nm in a standard configuration ​• SMA 905 fiber connector, no optical alignment required
                          ​• Triggering functions for easy integration (trigger in/out and delay) ​• Robust: fully built in alluminium
                          ​• Portable, fast and small size ​• LED Backlight indicator

                          For users looking for an affordable spectrometer with great resolution Sarspec offers the SPEC RES+ spectrometers range. With the best resolution/wavelength range ratio for a miniature CCD spectrometer the SPEC RES+ is the best option for Absorbance and Transmittance measurements as well for high throughput light source characterization.
                            • SPEC RES+ UV

                            • • Wavelength range: 180-400 nm
                              ​• Optical Resolution: 0.2nm
                              ​• 3648 pixels Toshiba CCD array detector
                              ​• 1800 grooves/mm grating blazed at 250 nm
                              ​• Best solution for high resolution UV
                              ​• LightScan software included

                              For UV enthusiasts that need really good resolution in that range the SPEC RES+ UV is the perfect choice. Covering the entire UV range with an optical resolution of 0.2 nm. It’s configuration complies a 10 µm slit, a 1800 grooves/mm grating blazed at 250 nm, collecting lens, SMA 905 connector and a Toshiba 3648 pixels CCD array.
                            • SPEC RES+ UV/VIS

                            • • Wavelength range: 180-880 nm
                              ​• Optical Resolution: 0.6 nm
                              ​• 3648 pixels Toshiba CCD array detector
                              ​• 600 grooves/mm grating blazed at 300 nm
                              ​• Great solution for Absorbance Measurements
                              ​• Software LightScan included

                              Specially configured for UV/Vis absorbance/transmittance measurements the SPEC RES+ UV/Vis offers great resolution from 180 to 880nm.

                              This model is configured with a 600 grooves/mm grating blazed at 300 nm, 10 µm slit, Collecting lens, SMA 905 Optical fiber connector and a Toshiba CCD array detector with 3648 pixels.
                               
                            • SPEC RES+ UV/VIS/NIR

                            • • ​Wavelength range: 200-1050 nm
                              ​• Optical Resolution: 0.75 nm
                              ​• 3648 pixels Toshiba CCD array detector
                              ​• 500 grooves/mm grating blazed at 300 nm
                              ​• Portable, Robust and Affordable
                              ​• LightScan software included

                              Configured with a 3648 pixels Toshiba CCD array, 10 µm slit for the best resolution, collecting lens, order sorting filters and SMA 905 fiber optic connector the SPEC RES+ UV/Vis/NIR is the perfect solution for replacing the traditional spectrophotometers with a technology that is more flexible and allows the user to get full spectra with milisecond time resolution.
                            • SPEC RES+ VIS/NIR

                            • • Wavelength range: 380-1050 nm
                              ​• Optical Resolution: 0.6 nm
                              ​• 3648 pixels Toshiba CCD array detector
                              ​• 600 grooves/mm grating blazed at 750 nm
                              ​• Order Sorting Filters Included
                              ​• Software LightScan included

                              Covering the entire visible and most of the NIR range with high resolution, the SPEC RES+ Vis/NIR is configured with a 600 grooves/mm blazed at 750 nm grating, 10 µm slit, Toshiba 3648 pixels CCD array, collecting lens, longpass filter and SMA 905 optical fiber connector.
                               
                          • SPEC SENSE+

                          • ​• Largest sensitive area, using 1000 µm height pixels ​• Back thinned CCD array detector with 2048 pixels
                            ​• Detection from 200-1100 nm ​• Great sensitivity and quantum efficiency up to 78%
                            ​• Great performance in the UV ​• Triggering functions for easy integration and synchronization
                            ​• SMA 905 fiber connector, no optical alignment required ​• High speed mini USB for full control of the spectrometer
                            ​• Software LightScan included • Fully built in aluminium with LED backlight indicator

                            Sarspec’s SPEC SENSE+ is a spectrometer specially built for low light level measurements such as Fluorescence and Raman but it also has the flexibility to be used in Absorbance, Transmittance, Irradiance and Reflectance measurements.
                              • SPEC SENSE+ UV

                              • • Wavelength range: 200-400 nm
                                ​• Quantum Efficiency of 65% at 300 nm
                                ​• Optical Resolution: 1.8 nm
                                ​• 1800 grooves/mm grating blazed at 250 nm
                                ​• 1 mm pixel height for a large detection area
                                ​• LightScan software included

                                Front side illuminated CCD’s have residual sensitivity in the UV range due the absorbance by the polysilicon gate. Combining the back thinned 2048 pixels CCD linear array detector from Hamamatsu with Quantum Efficiency of 65% at 300 nm (minimum of 50% within all UV region) with the large detection area offered by these detectors, Sarspec offers an unrivaled spectrometer for UV detection.

                                Being a spectrometer specially built for UV detection Sarspec was able to use a 1800 grooves/mm grating blazed at 250 nm allowing an optical resolution of 1.8 nm even with a 200 µm slit. This configuration includes also collecting lens to maximise sensitivity and SMA 905 connector.
                                 
                              • SPEC SENSE+ UV/VIS

                              • • Wavelength range: 200-880 nm
                                ​• Quantum Efficiency of 78% at 600 nm
                                ​• Back thinned 2048 pixels CCD array detector
                                ​• 600 grooves/mm grating blazed at 300 nm
                                ​• Collecting Lens included
                                ​• LightScan software included

                                The SPEC SENSE+ UV/Vis is configured with a 600 grooves/mm grating blazed at 300 nm, 200 µm slit and collecting lens allowing high sensitivity measurements in a wavelength range of 200-880 nm.
                              • SPEC SENSE+ UV/VIS/NIR

                              • ​• Wavelength range: 200-1050 nm
                                ​• Wide range and high sensitivity in one unit
                                ​• Back thinned 2048 CCD array detector
                                ​• 500 grooves/mm grating blazed at 300 nm
                                ​• 1 mm pixel height for a large detection area
                                ​• LightScan software included

                                The SPEC SENSE+ UV/Vis/NIR is a wide range, high sensitivity spectrometer that uses a back thinned CCD linear array from Hamamatsu with 1mm height pixels for the best sensitivity. This configuration uses a 500 grooves/mm grating blazed at 300 nm, a 200 µm slit allowing a significative amount of light collection, collecting lens, order sorting filters and SMA 905 optical fiber connector.
                              • SPEC SENSE+ FL

                              • • The best option for High Sensitivity Fluorescence
                                ​• Wavelength range: 300-1000 nm
                                ​• Quantum Efficiency of 75% at 500 nm
                                ​• 600 grooves/mm grating blazed at 500 nm
                                ​• Order sorting filters, collecting lens included
                                ​• External trigger (IN/OUT) for easy synchronization

                                The SPEC SENSE+ FL was specially designed for fluorescence measurements granting the best sensitivity for experiments, even in compounds with low quantum yield. The Quantum Efficiency (75% at 500 nm) of the back thinned CCD combined with the large pixel area, 200 µm slit, collecting lens and a 600 grooves/mm grating make these spectrometers the best option within it's wavelength range.
                                 
                            • SPEC SPEED+

                            • ​• Fast acquisition rate up to 2857 spectra per second using burst mode ​• 2 µs integration time with electronic shutter
                              ​• Back thinned CCD array detector with 2048 pixels ​• Largest sensitive area, using 1000 µm height pixels
                              ​• Detection from 200-1100 nm ​• Great sensitivity and quantum efficiency up to 78%
                              ​• Trigger functions for easy integration and synchronization ​• SMA 905 fiber connector, no optical alignment required
                              ​• High speed mini USB for full control of the spectrometer ​• Software LightScan+ Included
                              ​• Fully built in Alluminium with LED backlight indicator

                              With minimum integration time of 2 µs the SPEC SPEED+ is faster than any other spectrometer available using a CCD array. It was specially built for microseconds events including fast kinetics in chemical reactions, ignition processes and fluorescence monitoring among a large number of applications that need fast analysis.
                                • SPEC SPEED+ UV

                                • • Wavelength range: 200-400 nm
                                  • Optical Resolution: 0.5 nm
                                  • Fast acquisition: 2857 spectra/sec (full spectra)
                                  • 1800 grooves/mm grating blazed at 250 nm
                                  • Back thinned 2048 CCD array detector
                                  • LighScan+ software included

                                  Covering the entire UV range. the SPEC SPEED+ UV offers high acquisition rate and the optimized optical configuration with a 25 µm slit, a 1800 grooves per mm grating blazed at 250 nm allows also a great resolution of 0.5 nm. The detector is an Hamamatsu back thinned CCD array with 2048 pixels with 1 mm pixel height for high sensitivity. Software LightScan+ allows the best flexibility for time and sensitivity control of the spectrometer.
                                   
                                • SPEC SPEED+ UV/VIS

                                • • Wavelength range: 200-800 nm
                                  • Optical Resolution: 1.4 nm
                                  • Fast acquisition: 2857 spectra/sec (full spectra)
                                  • 600 grooves/mm grating blazed at 300 nm
                                  • Enhanced sensitivity option
                                  • LightScan+ software included

                                  The SPEC SPEED+ UV/Vis combines high speed, good resolution and high sensitivity in one spectrometer. Using a 25 µm slit, 600 lines/mm grating blazed at 300 nm, order sorting filters and a back thinned CCD detector array with 2048 pixels.
                                • SPEC SPEED+ UV/VIS/NIR

                                • ​• Wavelength range: 200-1050 nm
                                  ​• Fast acquisition: 2857 spectra/sec (full spectra)
                                  ​• Back thinned 2048 CCD array detector
                                  ​• 500 grooves/mm grating blazed at 300 nm
                                  ​• Enhanced sensitivity option
                                  ​• LightScan+ software included

                                  The SPEC SPEED+ UV/Vis/NIR is a wide range, high speed spectrometer that uses a back thinned CCD linear array from Hamamatsu allowing up to 2857 spectra per second. The full configuration includes a 25 µm slit, 500 grooves/mm grating blazed at 300 nm, order sorting filters and SMA 905 optical fiber connector.
                                • SPEC SPEED+ VIS/NIR

                                • • Wavelength range: 380-1050 nm
                                  • Optical Resolution: 1.4 nm
                                  • Enhanced sensitivity option
                                  • 600 grooves/mm grating blazed at 750 nm
                                  • Back thinned 2048 CCD array detector
                                  • LightScan+ software included

                                  For high speed acquisition in the NIR range the SPEC SPEED+ NIR is the best option available. Configured with a 25 µm slit, 600 lines/mm grating blazed at 750 nm, longpass filter and a back thinned CCD detector array with 2048 pixels.
                                   
                              • SPEC NIR

                              • ​• Detection from 660 to 2400nm ​• Allows the combination of Si and InGaAs detectores in one instrument
                                ​• TE cooled sensors ​• Best Optical Resolution in the martket
                                ​• Fast Scan Time up to 4ms ​• SMA 905 fiber connector, no optical alignment required
                                ​• Robust: fully built in aluminium ​​• Great solution for in-line applications
                                ​• Software LightScan included • Best Price

                                Combining an innovative, ultra fast micro electrical-mechanical mirror and single element detectors for a high performance and affordable solution.
                                    • SPEC NIR

                                    • The increasing market for Near Infrared Spectroscopy in the last years due to industry needs in raw material classification, polymer analysis, moisture quantification, saturated fatty acid identification among others lead to the development of different instrumentation, mainly for miniaturized solutions that can be portable, robust and easily integrated in an industrial environment.

                                      One of the biggest issues with NIR spectroscopy was the cost of the multi element detectors which made the investment for an NIR Spectrometer prohibitive for some industries. With the innovative design of SPEC NIR that uses single element detectors, Sarspec is able to offer an affordable solution ideal for transmission measurements with high stability and robustness.

                                      Also, the SPEC NIR is it the only miniaturized fiber optic spectrometer with the capability to use Silicon and InGaAs detectors for a detection range from 660 to 2400nm with the best optical resolution. This is possible due to the use of ultra fast periodic micro electectrical-mechanical mirrors with scan speeds up to 4ms and two single element detectors.
                                       
                                • User Configured

                                • Sarspec has four detector platforms available that were built for different purposes. The specifications and ordering information can be found in the options below. When purchasing a detector platform every customer in buying the detector, electronics and mirrors. The configuration is only complete with a slit, grating, filters (if required) and collecting lens (if required).
                                    • SPEC STD UC

                                    • With a wavelength range from 180 to 1100nm the SPEC STD provides an affordable solution for fast acquisition and good sensitivity.

                                      The detector platform includes the detector, electronics and mirrors. The configuration is only complete with a slit, grating, filters (if required) and collecting lens (if required).
                                    • SPEC RES+ UC

                                    • For the best resolution and affordable price in a user configured spectrometer we recommend the SPEC RES+ UC platform. The Toshiba detector with 3648 elements used in the this system can be combined with narrow slits for optical resolutions better that 0.1nm. With peak wavelength at 550nm this system offers great sensitivity in the visible range.

                                      The detector platform includes the detector, electronics and mirrors. The configuration is only complete with a slit, grating, filters (if required) and collecting lens (if required).
                                       
                                    • SPEC SENSE+ UC

                                    • Configured with a Hamamatsu Back-Thinned ccd-array detector with 2048 elements. Combining the excelent quantum efficiency of 78% and height (1mm) of each element for maximum light collection the SPEC SENSE+ offers great sensitivity, including the UV range.

                                      The detector platform includes the detector, electronics and mirrors. The configuration is only complete with a slit, grating, filters (if required) and collecting lens (if required).
                                    • SPEC SPEED+ UC

                                    • Fastest spectrometer platform of its kind allowing up to 2857 spectra per second. Ideal for ultafast measurements, has a detection range from 200 to 1100nm. With 78% quantum efficiency at peak, combines sensitivity and speed.

                                      The detector platform includes the detector, electronics and mirrors. The configuration is only complete with a slit, grating, filters (if required) and collecting lens (if required).
                                       
                                  • Software

                                  • LightScan and LightScan+ are spectroscopy softwares dedicated to control and perform data acquisistion from Sarspec’s SPEC Spectrometers range. LightScan applies to SPEC STD, RES+ and SENSE+ models and LightScan+ is specific for the SPEED+ range alowing additional control of the detector electronics with faster acquisition and shorter integration time. With any of these options every user can expect:

                                    ​• Really simple to use, only a few minutes to get results
                                    ​• Modular construction: only the necessary information is available in each application module
                                    ​• Full control of the spectrometer in the Spectum tab (integration time, gain, average, smoothing, trigger)
                                    ​• Intuitive graphic functions with single and multi peak finding and min/max with threshold value
                                    ​• Modules for Absorbance, Reflectance, Transmittance and Fluorescence with external calibration
                                    ​• Samples measured as calibrated, unclaibrated or free measurements for maximum flexibility
                                    ​• Kinetics module for single or multiwavelength acquisition in any measurement type vs. time
                                    ​• One file per spectrum and one file for all spectra saved for complete flexibility
                                    ​• Reports for analisys and calibration including spectra and results list for samples and standards
                                    ​• Files saved as text for easy importing to other programs such as Excel™, Origin™, Matlab™, etc.
                                    ​• Burst mode module for high speed acquisition (LightScan+ only)
                                      • LightScan

                                      • LightScan software was developed to be simple to work with, but at the same time efficient and powerfull. Within a few minutes users can get results without complex settings.

                                        The LightScan software is divided in the Spectrum tab and the Application Modules for Absorbance, Transmittance, Reflectance and Fluorescence. Each one of these modules has one Calibration Module.

                                        The Kinetics module is specific for time measurements where it's possible to select any of the measurements above.
                                      • LightScan+

                                      • LightScan+ software includes all the available features in LightScan and some more specific to allow high speed data acquisition (up to 2857 spectra/second) for the spectrometers SPEC SPEED+ range.

                                        LightScan+ provides access to parameters such as exposure time, line time, electronic shutter and Low Noise mode (MPP) that allows optimization of time and sensitivity settings for optimum results in ultra fast measurements. Also available is μs time scale resolution both for integration and trigger, allowing high resolution synchronization to external devices and short duration and/or period events.
                                         
                                    • Light Sources

                                        • Xenon Flashlamp

                                        • State-of-the-art pulsed Xenon light source with the following main features:

                                          • Pulsed Xenon lamp with high stability ​• TTL pulse flash control
                                          ​• High radiant intensity ​• Local and remote intensity adjust
                                          ​​• Continuous emission from 190-2000+ nm ​• High flash rate up to 278 Hz
                                          ​• Maximum power: 6 W ​• Ideal solution for optically degradable samples
                                          ​• Small, powerfull and reliable with EMI shielding
                                              • Light Source Xenon Flashlamp

                                              • The flexibility of this light source makes it a great solution for Fluorescence/Phosphorescence measurements due the high energy pulses and UV performance. Its large spectrum and stability makes it suitable also for Absorbance, Reflectance and Transmittance. Its high intensity in the UV makes it the perfect solution for Fluorescence measurements in biological samples.

                                                Sarspec's LS-XeF is designed to be the state-of-the-art pulsed Xenon light source, providing microsecond-duration pulses of broadband light with exceptional arc stability and life characteristics. This light source is a compact solution with a high radiant and powerful flash lamp, offering a wide range of flash energy and repetition rate in a pre-aligned module.

                                                This light source can be synchronized with all Sarspec’s spectrometers where the flashes frequency and delay can be controlled. Combined with Sarspec’s Spectrometers, Optical Fibers and Accessories it’s a great and flexible solution for every laboratory.
                                                 
                                          • Xenon 300

                                          • Sarspec’s LS-Xe300 is the most intense fiber coupled light source in the market incorporating a 300 W continuous Xenon lamp.

                                            ​• Continuous Xenon arc lamp light source ​• High power up to 320 W
                                            ​• Manual power adjust from 180 W to 320 W ​• Wavelength range from 190 to 2000+ nm
                                            ​• Shutter included ​• Slide filter holder included (internal)
                                            ​• Remote control for shutter, intensity and lamp • LED Indicator for lamp operation and replacement
                                            ​• High intensity in the 200-400 nm range ​• Safety Interlock for lid opening
                                            ​• Fiber optic coupling or air transmission
                                                • Xenon 300

                                                • Providing brighter light than its competitors, this light source has a high performance, an extremely powerful lamp with very high light intensity and a wavelength range from 190 nm to more than 2000 nm. It can be used with an optical fiber or air transmission.

                                                  The very small size of the arc lamp makes it possible to focus the light from the lamp with good precision. This equipment achieve maximum efficiency with safety concerns.

                                                  If it’s too much intensity for a specific application its always possible to adjust localy (knob) or remotely the intensity for a minimum of 180 W.

                                                  Specially designed for Fluorescence measurements it can be attached to our multipurpose cuvette holder via a specially built optical fiber bundle that can handle the heat generated by the source or by direct attach. This light source can also be used for air transmission with the collimated beam coupled to an optical system or for high power irradiation.
                                                   
                                            • Deuterium Tungsten

                                            • LS-DW is a complete UV-VIS light source with an wavelength range that goes from 200-1100 nm (optionally from 185-1100 nm) that is used for Absorbance, Reflectance, Transmittance and Fluorescence. It includes a deuterium and a tungsten lamp in shine-through array, shutter and SMA 905 connector.

                                              ​​• Complete UV/Vis/NIR Light Source ​• Low power consumption
                                              ​• Wavelength range: 200-1100 nm or 185-1100nm ​• Extended lifetime of the lamps
                                              ​• High stability ​• Shutter included
                                              ​• Independent operation of lamps ​• Remote control (shutter, lamp selection)
                                              ​• Short warm-up time ​• Ideal for Absorbance and Transmittance measurements
                                              ​• Reliable, Compact and Efficient
                                                  • LS-DW

                                                  • The useable wavelenght range from this Light Source is from 200 to 1100 nm but can be extended to 185 nm with a Deep UV optional Deuterium lamp. Both lamps can work independently in the spectral region of interest for extended life time. The lamps are easily replaceable due to a simple connection and to a pre-aligned mounting ring.

                                                    LS-DW is a complete UV/VIS/NIR light source with a deuterium and a tungsten-halogen lamp in shine-through configuration, shutter and SMA 905 connector. Due to it’s high stability and reliability is the perfect solution for absorbance and transmittance measurements.

                                                    In all supplied sources is also included a shutter that allows a simple operation for dark measurements and eliminates the need to turn off the lamps resulting in more stability and extended lifetime.

                                                    The remote control allows lamp selection and shutter operation via D-SUB connection.
                                                     
                                              • Deuterium Tungsten HPOWER

                                              • LS-DWHP is the most complete high power UV-VIS light source with powerful deuterium and tungsten lamps in shine-through array and a spectral distribution from 190-3000 nm. Its main applications are Transmittance, Absorbance and Reflectance.

                                                ​​• Complete High Power UV/Vis/NIR Light Source ​​• Deuterium (30 W) and Tungsten-Halogen (20 W) lamps
                                                ​​• Filter slot included for 12,5 mm (1/2’’) diameter filters ​​​• Shutter included
                                                ​• Independent operation of Lamps ​• Easy lamps replacement
                                                ​• Robust, reliable and flexible ​• SMA 905 connector
                                                • Focusing lens with 12,7 mm diameter for better throughput ​• Optically isolated remote operation (shutter and lamp selection)
                                                    • LS-DWHP

                                                    • This light source includes a slot filter holder which makes the change between Sarspec’s slide filters quite easy. This feature is also very convenient for fluorescence measurements. By adding neutral density filters it’s also possible to perform Absorbance and Transmittance measurements.

                                                      With 30 W Deuterium and 20 W Tungsten-Halogen lamps, the LS-DWHP is the most complete high power UV/VIS/NIR light source. Configured in shine-through design, with 12.7 focusing lens for maximum light collection, local or remote operation and SMA 905 connector. Both lamps can work independently in the spectral region of interest for extended life time, and are easily replaceable.

                                                      In all supplied sources is also included a shutter which allows a simple operation for dark measurements and eliminates the need to turn off the lamps.

                                                      The remote operation allows lamp selection and shutter control via D-SUB connection with a TTL compatible signal.
                                                       
                                                • Tungsten

                                                • The most complete Vis-NIR light source in the market integrating a tungsten lamp with manual power control, filter holder and SMA 905 connector. LS-W has a range from 300 to 3000 nm and can be used in techniques such Absorbance, Transmittance, Reflectance, Fluorescence and even Colorimetry.

                                                  ​• Complete and flexible light source for Vis/NIR regions ​​• Four lamps available with 7, 14, 20 and 25 W
                                                  • Local knob for intensity control ​​• Shutter included
                                                  ​​• Remote analog and PWM intensity control ​• Filter slot included
                                                  ​​• 12.7 mm diameter focusing lens to maximize light collection • Easy replacement of the lamp
                                                  • Wavelength range: 380 (300 for 20 W) to 3000 nm (7, 14 and 25 W lamps) ​• Optically isolated input for shutter and lamp operation
                                                      • LS-W

                                                      • Sarspec’s LS-W is the most complete Vis-NIR light source in the market integrating a Tungsten-Halogen lamp with manual intensity control, shutter, filter holder and SMA 905 connector. This compact equipment offers the possibility to have four different Tungsten-Halogen lamps (7, 14, 20 and 25 W) with wavelength ranges from 300-3000 nm for the 20 W version and 380-3000 nm for the remaining ones.

                                                        This light source is a great option for Reflectance such as color measurements. For users that want to perform Fluorescence measurements we advise the 25 W version or the 7 W version for Absorbance and Transmittance. The light source allows lamps interchangeability without any hardware modification.

                                                        All four configurations have local (knob) and remote intensity control which allows users to select the right intensity for their applications, allowing higher flexibility.
                                                        All features from LS-W can be controlled remotely via D-SUB connector and TTL compatible signals, namelly the shutter, intensity control and lamp operation.
                                                         
                                                  • LED

                                                  • LS-LED it's a versatile light source to use in Fluorescence applications since it has an extremely easy and unique system to change between LEDs. You can choose from more than 60 LEDs available the one that it will correspond to your needs.

                                                    ​• LED light source with High Power LEDs ​• More than 60 interchangeable LEDs
                                                    ​• Patent pending innovative LED slide concept ​• Pulsed/Continuous/Modulation modes
                                                    ​• Available wavelengths from 275 nm to 4600 nm ​• Ideal for Fluorescence measurements
                                                    ​• External and Internal trigger ​• Local/Remote intensity control
                                                    ​• High stability ​• Small, Smart and Affordable
                                                        • LS-LED

                                                        • All available LED light sources in the market were until now either single channel with complex LED interchangeability (when possible) or expensive and complex multichannel sources. With this patent pending approach, Sarspec makes it easy to change between different LEDs/wavelengths just by inserting a LED slide into a slot holder.

                                                          The LED slides are ready to use without the need of any wire connections. With this approach it’s possible to use any of more than 60 LEDs/Wavelengths available, purchasing only one light source and adding the required LEDs ranging from 275 nm to 4600 nm.

                                                          This LED light source is the typical application for Fluorescence and to maximize sensitivity Sarspec supplies high power LEDs with optical power up to 750 mW.
                                                           
                                                    • MIR

                                                    • LS-MIR is a complete and flexible Light Source for NIR / SWIR / MWIR regions, providing a wavelength range from 500 to 5000 nm and it can be used with techniques such as Absorbance, Transmittance and Reflectance.

                                                      ​​• Complete light source for NIR/SWIR/MWIR regions ​• Silicon Nitride emitter
                                                      ​• Wavelength range from 500 to 5000+ nm ​• 5000 hours emitter lifetime
                                                      ​• Local Knob for intensity control ​• Easy replacement of the lamp
                                                      ​• Shutter and filter slot included ​• Remote analog and PWM intensity control
                                                      ​• Optically isolatedinput for shutter and emitter operation ​• 12.7 mm diameter focusing lens for optimum light coupling
                                                          • LS-MIR

                                                          • With one 18 W Silicon Nitride emitter, the Light Source LS-MIR was specially designed for infrared applications providing a wavelength range from 500 to 5000+ nm. This is an high flexibility product that includes shutter, slide filter holder, intensity control and remote operation.

                                                            The flexibility of this light source is granted not only for its wide wavelength range but also for the included slide filter holder allowing the selection of a specific range. Tthe intensity control offers the user the possibility to select the correct intensity for each application.

                                                            The LS-MIR includes a shutter to avoid overexpose the sample without turning off the lamp.
                                                             
                                                      • Optical Fibers/ Probes

                                                          • Optical Fibers

                                                          • Using optical fibers to guide light ensures high transmission and flexibility in spectroscopy measurements, as one can easily connect different components to build a suitable solution for each application without complex optical designs. Sarspec is specialized in high quality optical fibers for the best results.
                                                                • Optical Fibers

                                                                • All Sarspec fiber-optic cables are built with a numerical aperture (N.A.) of 0.22 and uses standard SMA 905 connectors for easy coupling, without the need of any optical alignment with spectrometers, light sources and sampling accessories.

                                                                  It’s important to select some key specifications in order to get the right optical fiber, namely: wavelength range, core diameter, length, jacketing and type (patch cord or bifurcated).

                                                                  In the tabs below is given a simple explanation about the components and specifications of our optical fibers as well for how to configure an optical fiber.

                                                                  Even though the information focus on standard products, it’s important to mention that as a manufacturer Sarspec can build specific solutions that matches customer's requirements.
                                                                   
                                                            • Optical Fiber Probes

                                                            • Sarspec offers a full range of Probes for Reflectance and Transmittance/Absorbance measurements in surfaces, powders, solids, solutions, etc.
                                                              Our probes are designed considering the highest standards and precision for the most reliable analytical results being fully built in stainless steel for maximum robustness, allowing to work in two different wavelength ranges, UV/Vis (180-1200 nm) or Vis/NIR (300-2400 nm).
                                                              The typical design consists of a ‘Y’ shaped probe where one section is connected to the light source for sample illumination and the other section is connected to the spectrometer for sample characterization.
                                                              Sarspec customizes probes for specific applications either in length, temperature, pressure and chemical resistance, specific threads for reactor coupling, among others.
                                                                • Transmission Probes

                                                                • Sarspec’s transmission probes are the right choice for immerse Transmittance/Absorbance measurements. This solution is ideal for measurements in reaction vessels in real time mode.

                                                                  Built for Absorbance and Transmittance measurements in liquid samples
                                                                  Great solution for real time reaction monitoring
                                                                  Available pathlengths of 2, 5 and 10 mm
                                                                  Probe and jacket in stainless steel for maximum resistance
                                                                • Reflection Probes

                                                                • A reflection probe is used to get spectral information of specular or diffuse reflectance from a surface, fluorescence from solid surfaces, or backscattering and fluorescence in solutions and powders. Sarspec's reflection probes have the following characteristics:

                                                                  • Built for Reflectance measurements
                                                                  • Allows Specular and Diffuse Reflectance measurements when combined with the probe holder (PH)
                                                                  • Six illumination fibers around one collection fiber configuration as standard
                                                                  • Available in the UV/Vis or Vis/NIR wavelength ranges
                                                                   
                                                              • Accessories

                                                                  • Cuvette Holders

                                                                  • Cuvette Holders are useful equipments for laboratory measurements, designed to operate perfectly with sarspec Spectrometers and Light Sources for techniques as Absorption / Trasmission and Fluorescence.

                                                                    Sarspec offers you various options from a combined system that can perform absorbance/transmittance and fluorescence simultaneously or temperature controlled.

                                                                    CUVETTE HOLDER

                                                                    Affordable solution that can be used for Absorbance and Fluorescence measurements.
                                                                      • Cuvette Holder

                                                                      • Sarspec’s Cuvette Holder - CH is a flexible accessory that can be used to perform Absorbance/Transmittance and Fluorescence measurements. Each configuration is easily interchangeable for both types of measurement and can optionally be performed simultaneously.

                                                                        ​• Suitable for Absorbance and Fluorescence
                                                                        ​• Small, flexible and affordable
                                                                        ​• Rack for four cuvettes
                                                                        ​• Cover included for photosensitive samples
                                                                        ​• Fiber optic couple with SMA905 connectors
                                                                        ​• Collimating lenses with adjustable focal length
                                                                      • Cuvette Holder Multipurpose

                                                                      • Sarspec CH-MP is a flexible cuvette holder as it’s small, portable and a complete solution for Absorbance / Transmittance and Fluorescence measurements.

                                                                        ​• Built for 10 mm pathlength cuvettes
                                                                        ​• Absorbance, Fluorescence and Raman measurements
                                                                        ​• 12.7 mm collimating lens with adjustable SMA connector
                                                                        ​• Flexibility – 4 entry/exit ports each one with filter slots
                                                                        ​• Optional signal enhancing mirrors
                                                                        ​• Optional direct attach

                                                                        The 12.7 mm collimating lenses with adjustable SMA connector allow the illumination of larger sample area and collection of more light, making it the best solution for low light measurements.

                                                                        The filters, large diameter lens and optional signal enhancing mirrors (CH-MP-EM) combined make this product a great solution for the best results for Fluorescence measurements.
                                                                         
                                                                      • Peltier Cuvette Holder CH-QPOD2E

                                                                      • The CH-QPOD® 2e (Quantum Northwest, Inc.) is a complete sample compartment for fiber optic spectroscopy, including a Peltier-controlled cuvette holder with magnetic stirring, and fused silica lens systems with SMA fiber optic connectors. The qpod 2e housing contains a PID temperature controller that is operated via Bluetooth wireless or USB using the computer program Q-Blue.

                                                                        ​• Peltier temperature control
                                                                        ​• Temperature range from -30 to +110 ºC
                                                                        ​• USB or wireless Bluetooth control
                                                                        ​• Magnetic stirring and dry gas purge
                                                                    • Collimating Lenses

                                                                    • Collimating lenses are useful for any optical setup that requires the acceptance or transmission of parallel beams of light at the illumination source, at the entrance optics, or at both ends (illumination and read) of the setup.

                                                                      ​• Used to focus or collimate a light beam
                                                                      ​• Two options: 6 mm and 12.7 mm diameters
                                                                      ​• Standard UNS 1/4''-36 for SM connection
                                                                      ​• Adjustable SMA connector
                                                                          • Collimating Lens

                                                                          • The main characteristic is the ability to create a well-directed beam with a well-defined diameter, allowing therefore a uniform illumination of the sample in study by converting divergent beans of light into a parallel beam. For this to occur, the light emitting element must be placed at the focus of the lens.On the other side, if the incident light is already collimated the collimating lens will focus the light in its focal distance.

                                                                            All of our collimators covers the UV-VIS-NIR range and have a two-part housing of aluminium, a screw to adjust the position of the SMA connector, allowing users to adjust the focus.

                                                                            Sarspec has available two types of collimators with 6 mm and 12.7 mm lens.
                                                                             
                                                                      • In-Line Filter Holder

                                                                      • The purpose of the In-Line Filter Holder is to filter light in the optical fiber path by connecting two optical fibers. Sarspec's In-Line Filter Holder has the following characteristics:

                                                                        ​• Connect two optical fibers via SMA 905
                                                                        ​• Use up to three 3 mm thick filters simultaneously​
                                                                        ​• Set for 12.5 mm / 1/2" diameter filters
                                                                        ​• Includes two CL1 collimating lenses
                                                                            • In-Line Filter Holder

                                                                            • Sarspec’s In-Line Filter Holder (ILFH) can be used with up to 3 filters with 3 mm thick x 12.5 mm / 1/2” diameter and includes 2 collimating lenses CL1 and 2 spacers.

                                                                              With the filters available from Sarspec it is possible to choose the right illumination or specific wavelengths to irradiate or collect light. The two SMA 905 connectors allows the coupling with two optical fibers.

                                                                              The filters are easily replaceable by unscrewing the two-part housing. Please check our filter section for the available filters for this accessory.
                                                                               
                                                                        • Optical Filters

                                                                        • The optical filters available can be purchased as round unmounted filters or for easy coupling as slide filters. Sarspec supplies optical filters with the following characteristics:

                                                                          ​• Large number of options available
                                                                          ​• Round unmounted filters for in-line filter holder
                                                                          ​• Slide mounted filters to use with Sarspec's accessories
                                                                          ​• 12.5 mm x 3 mm round filters as standard
                                                                              • Optical Filters

                                                                              • The optical filters available can be purchased as round unmounted filters or for easy coupling as slide filters.

                                                                                Slide Filters are filters mounted in aluminium bars and inserted in the slots available in Sarspec’s Light Sources and Cuvette holders. This makes it very easy to change between filters without disassembling the light sources. Sarspec has available a large number of optical filters including :

                                                                                Longpass Filters – Have low transmission in the shortwave region (blocking range) and high transmission in the longwave region (pass band). The range between 225 nm and 1000 nm has very steep transmission edges.

                                                                                Shortpass Filters – The passband of shortpass filters is at lower wavelengths than the blocking range, compared to longpass filters. Basically they block longer wavelengths.

                                                                                Bandpass Filters – Have a transmission band or bands surrounded by blocking bands allowing only a portion of the spectrum to pass. They are useful for high transmission in their designed spectrum while blocking other wavelengths.

                                                                                Neutral Density Filters - reduce the intensity almost equally in a specific wavelength range.
                                                                                 
                                                                          • Flow Cells

                                                                          • Sarspec's Flow Cells are the ideal choice for the analysis in a continuous flow system. Our flow cells allow two types of measurement techniques: Absorbance and Fluorescence.

                                                                            • Two types available: Absorbance and Fluorescence
                                                                            ​• Built in stainless steel or PTFE
                                                                            ​• Sapphire windows for extreme resistance and SMA Connectors
                                                                            ​• Compatible with standard HPLC fittings.
                                                                                • Flow Cells

                                                                                • Flow Cells are available in stainless steel or PTFE according the applications, with 10 mm pathlength and sealed sapphire windows in each of the fiber optic connectors. Our flows cells allow two types of measurement techniques: Absorbance and Fluorescence.

                                                                                  For Absorbance, cells are designed in Z shape with 10 mm pathlength and for Fluorescence the cells are designed with a 90º configuration between excitation and emission. Both configurations are designed to provide optimum flow, maximum light intensity and minimum bubble entrapment.

                                                                                  The robustness of this system is algo granted by the use of Sapphire windows for wide wavelength range transmission (180-5000 nm) and great resistance to mechanical ware and harsh chemicals.

                                                                                  Each flow cell is delivered with the required sapphire windows, SMA connectors, chemically resistant seals, 1/16’’ (Absorbance) or 1/8" (Fluorescence) O.D. tube fittings and 10 cm tubing.
                                                                                   
                                                                            • Reflectance Standards

                                                                            • Sarspec has available two types of reflectance standards, for diffuse and specular reflectance with the following characteristics:

                                                                              ​• For diffuse and specular reflectance
                                                                              ​• Wavelength range from 250 to 2500 nm
                                                                              ​• 50 mm diameter
                                                                              ​• Anodized aluminium housing
                                                                                  • Reflectance Standards

                                                                                  • Sarspec has available two types of reflectance standards, for diffuse and specular reflectance.

                                                                                    The specular reflectance type consists of a 50 mm mirror with fused silica substrate coated with Al-MgF2 for high specular reflectivity in a wavelength range from 250 to 2500 nm.

                                                                                    For diffuse reflectance all Sarspec standards use optical PTFE which consists of a pure polytetrafluorethylene (PTFE) disc with 50 mm diameter. As a result of its incomparable whiteness and purity, optical PTFE achieves virtually ideal Lambertian reflectance properties with a reflectivity coefficient of up to 98% in a broad wavelength range from 250 to 2500 nm. Aditional advantages when using optical PTFE is its high UV stability, universal chemical resistance and can be easily cleaned.

                                                                                    Sarspec offers one specular standard and three diffuse standards corresponding to reflectivities of 98%, 50% and 10%. There’s also the possibility of customization for different sizes or reflectivities.