• Offer Profile
  • HBE is developing and producing hydraulic components, oil tanks, bellhousings and couplings for the drive and fluid technology.

    Highest technical standards, extensive flexibility concerning customer requirements and order processing as well as direct supply from stock within shortest delivery times ensure the economical efficiency of HBE products.
Product Portfolio
  • Steel or stainless steel oil tanks

  • The ready to install HBE steel oil tanks are manufactured from the material S235JR (St37) and are sandblasted and coated both from the inside and outside the tank. That is why the tanks are resistant against hydraulic oil on mineral oil base and low-flammable fluids. Suitable oil sumps are available as well as a comprehensive range of accessories like cleaning covers, sealing gaskets, level indicators and incorporators.

    Type and delivery extent for HBE standard

    • Leak test by two colour check
    • Gasket 15 x 5 mm made of Perbunan (NBR) in case of screwed tank lid
    • Drain plug DIN 908 + Cu gasket for oil drain at the tank

    Available for extra charge
    • Final varnish
    • Individual machining of tank, tank lid or oil sumps
    • Stainless steel 1.4301 (V2A) resp. 1.4571 (V4A), sandblasted inside and outside with glass beards
      • Standard tank series WN-LC
        NG 40 - 400 L

      • Standard tank series STB
        NG 40 - 2000 L

      • Oil sumps for tanks
        series WN-LC / STB

      • Tanks according to DIN 24 339 (1993)
        NG 63 - 1250 L

      • Oil sumps for tanks
        according to DIN 24339

      • Tanks according to customer drawing up to 20,000 L

    • Aluminium oil tanks

    • The HBE aluminium oil tanks with an all-round fluting are characterised by a good heat dissipation. The stable casted bodies are stackable in all tank sizes, which leads to low freight costs and a space saving storage. Suitable tank lids are according to customer’s drawing (coating included, if desired), ready to install for all sizes and can be delivered short term.

      Type extent
      • AB 30 – AB 70 available with feet or castors alternatively
      • Flat gasket made of rubber cork between tank lid and tank for
      • AB 3.5 – AB 20
      • Toroidal sealing ring (endless, without contact spot) 6 mm Ø NBR for AB 30 – AB 70
        • ALUMINIUM OIL TANKS AB 3,5

        • Effective capacity approx. 3 L · weight 1,0 kg · stackable
        • ALUMINIUM OIL TANKS AB 6,5

        • Effective capacity approx. 6 L · weight 1,6 kg · stackable
        • ALUMINIUM OIL TANKS AB 12 NR

        • Effective capacity approx. 11 L · weight 3 kg · stackable
        • ALUMINIUM OIL TANKS AB 20

        • Effective capacity approx. 17 L · weight 4,4 kg · stackable
        • ALUMINIUM OIL TANKS AB 30 NR

        • Effective capacity approx. 26 L · weight 7 kg · stackable
        • ALUMINIUM OIL TANKS AB 44

        • Effective capacity approx. 40 L · weight 10 kg · stackable
        • ALUMINIUM OIL TANKS AB 70

        • Effective capacity approx. 63 L · weight 12 kg · stackable
        • OIL SUMPS FOR ALUMINIUM TANKS
          ÖW 12 – ÖW 70

        • For aluminium tanks AB 12 – AB 70
      • Hydraulic accessories - Cleaning covers, level oil gauges, level switches, fillers

          • ALUMINIUM CLEANING COVERS (DIN 24339) WITH FORM GASKET

            • Cleaning cover RD 250-4 and RD 250/235 for steel oil tanks of low size
            • Cleaning cover RD 350 and 475 acc. to DIN 24339
            • Formgasket available of perbunan (NBR standard), viton (FPM) and EPDM
            • Screw torque for this cleaning covers 20 Nm max.
            • Test pressure for all RD types 0.5 bar max.
            • Company logo can be casted on
            • All sizes also available in steel and stainless steel
          • ALUMINIUM CLEANING COVERS WITH O-RING GASKET FLANGE ASSEMBLING

            • Cleaning cover RD 320-6 with flange assembling
            • O-ring gasket available of perbunan (NBR standard), viton (FPM) and EPDM
            • Screw torque for RD 320-6 20 Nm max.
            • Test pressure for all RD types 0.5 bar max.
            • Company logo can be casted on
          • ALUMINIUM CLEANING COVERS WITH O-RING GASKET CENTRAL ASSEMBLING

            • Cleaning cover RD 235 und RD 345 with central assembling
            • O-ring gasket available of perbunan (NBR standard) or viton (FPM)
            • Screw torque for RD 235 and RD 345 40 Nm max.
            • Test pressure for all RD types 0.5 bar max.
            • Company logo can be casted on
          • LEVEL OIL GAUGES

          • MATERIALS
            • Case: St (powder coated)
            • Plug: PA
            • Scale plates: PVC
            • Gaskets: NBR (optionally FPM)
            • Approriate for hydraulic oils HL and HLP
            TECHNICAL DATA
            • Application range: –20°C … +80°C
            • Indication range thermometer:
            • ÖS 76: +20°C … +80°C
            • ÖS 127/176/254: –10°C … +80°C
            • Screwed starting torque: 8 Nm max.
          • FILLERS

          • MATERIALS / TECHNICAL DATA
            • Airscoop: Steel, chrome coated
            • Flange: Steel, chrome coated
            • Air fi lter element: 10 μm
            • Filler sieve: Steel, zinc coated
            • Gaskets: cork, Perbunan (NBR)
          • LEVEL OIL GAUGES

          • Suitable for hydraulic oils HL and HLP
            • Optional use with probe therm
            • Alternatively available as brake contact or make contact
            • Contact box acc. to DIN EN 175301-803-B / ISO6952
          • LEVEL SWITCHES SERIE NS 1
            WITH 1 SWITCH CONTACT

            • Electrical level supervision
            • Appropriate for mineral oil, diesel and benzine
            • 1 switch contact
            • Electrical circuit for level, min / max
            • Standard version level max = contact open
          • LEVEL SWITCHES SERIE NS 2
            WITH 2 SWITCH CONTACTS

            • Electrical level supervision
            • Appropriate for mineral oil, diesel and benzine
            • 2 switch contacts
            • Electrical circuit for level, min / max
            • Standard version level max = contact open
          • LEVEL SWITCHES SERIE NS 1-TE
            WITH TEMPERATURE SWITCH

            • Electrical level supervision
            • Appropriate for mineral oil, diesel and benzine
            • 1 switch contact
            • Electrical circuit for level, min / max
            • Standard version level max = contact open
          • LEVEL SWITCHES SERIE NS 1-VR
            WITH VARIABLE SWITCH CONTACT

            • Electrical level supervision
            • Appropriate for mineral oil, diesel and benzine
            • The indication level can be adjusted between 200-500 mm by cutting the stem of the length required
        • Tank heater

          • Standard devices of 0.25 kW–5 kW available
          • Devices for EX-protection and special devices on request
          • A calculation programme for determination of the required tank heater is available on request

          Field of application
          Preheating of hydraulic oil on mineral basis for a fast reaching of the operating temperature at hydraulic units. The optimum viscosity decreases the wear of the hydraulic components.
            • VR IMMERSION HEATERS WITH MAGNETIC CLAMP

              • For preheating of hydraulic oil
              • No mounting effort, ideal solution to retrofit existing installations
              • Horizontal or vertical arrangement, low minimum oil level
              • Medium touched pieces stainless steel (14571), brass and plastics respectively
              • Welded type
              • Magnetic clamps for fixing at tank bottom/partition wall
              • Protection IP 68
              • Integrated thermostat with switch-off temperature 40°C (standard)
              • Integrated temperature limiter
              • Surface charge: 1.2 W/cm2 for HLP
              • 0.6 W/cm2 for HFA/HFC/HFD-R
            • CARTRIDGE SCREWED-IN HEATERS

              • Cartridge heaters for preheating of hydraulic oil
              • Exchangeable ceramic heating insert (mounting/dismounting possible without evacuation of oil)
              • Bright galvanized steel cap
              • For horizontal mounting under oil level
              • Material: Steel (further materials on request)
              • Surface charge 1.5 W/cm2 for hydraulic oils
              • Protection IP 65
              • Wiring schemes for different mains voltages on request
            • CARTRIDGE SCREWED-IN HEATERS WITH TEMPERATURE ADJUSTMENT

              • Cartridge heaters for preheating of hydraulic oil
              • Temperature adjustment for internal (THI) and external regulation (THA), single-pole 0°-85°C, 16 amp
              • Exchangeable ceramic heating insert(mounting/dismounting possible without evacuation of oil)
              • Bright galvanized steel cap
              • For horizontal mounting under oil level
              • Material: Steel (further materials on request)
              • Surface charge 1.5 W/cm2 for hydraulic oils
              • Protection IP 54
              • Wiring schemes for different mains voltages on request
            • RHK-TUBE SCREWED-IN HEATERS

              • Tube screwed-in heater for preheating of hydraulic oil
              • Bright galvanized steel cap
              • For horizontal mounting under oil level
              • Material: Steel (further materials on request)
              • Surface charge 1.5 W/cm2 for hydraulic oils
              • Protection IP 65
              • Wiring schemes for different mains voltages on request
            • RHK-TH-TUBE SCREWED-IN HEATERS WITH TEMPERATURE ADJUSTMENT

              • Tube screwed-in heater for preheating of hydraulic oil
              • Temperature adjustment for internal (THI) and external regulation (THA), single-pole 0-85°C, 16 amp
              • Bright galvanized steel cap
              • For horizontal mounting under oil level
              • Material: Steel (further materials on request)
              • Surface charge 1.5 W/cm2 for hydraulic oils
              • Protection IP 54
              • Wiring schemes for different mains voltages on request
          • Bellhousings, foot brackets, damping rings and damping rods

                • BELLHOUSINGS RIGID

                  • Connection elements between IEC electric and petrol motor and hydraulic pump
                  • Available for nearly all hydraulic pumps ex stock at short notice
                  • Rigid (Form A) and noise absorbing model (Form B) according to VDMA 24561
                • BELLHOUSINGS DAMPED

                  • Standard bellhousings made of aluminium
                  • Bellhousings made of steel are available in all dimensions at short notice
                  • A calculation programme is available on CD ROM free of charge for easy selection of the required bellhousing and type of coupling. Please request this online
                • NEMA ADAPTOR

                  • Adapter for NEMA motors (U.S. standard) in conjunction with standard bellhousings
                • FOOTBRACKETS

                  • Aluminium foot brackets for the horizontal installation of motor-bellhousing-pump
                  • Enables separate assembly/disassembly of
                    motor and pump
                • DAMPING RODS

                  • Applied to reduce noise and dampen vibrations
                  • Finish-worked for IEC and NEMA motors and foot brackets available ex stock
                • DAMPING FLANGES

                  • Damping flanges are used in conjunction with aluminium or steel bellhousings as well as pump brackets
                  • No metallic bonding of the two vulcanised flange surfaces
                  • Sound level reduction up to 8 dB (A)
                  • Motor oil aluminium / Perbunan Aluminium
                • DAMPING RINGS

                  • With V1 design, application between bellhousing and oil tank cover or between bell housing and foot bracket with IMB 5 design
                  • No metallic bonding of the two vulcanised assembly flanges
                  • Noise reduction of approx. 3–5 dB (A)
                • MOUNTING FLANGES

                • Simplified assembly/disassembly of the drive unit motor/pump incl. pressure line with V1 design
                • GASKETS

                • Gaskets made from rubberised cork for bell housings, assembly flanges and gear pumps
                • Bellhousings with integrated oil air cooler

                  • Round bellhousing with oil air cooler, series PTÖK
                  • Model series for electrical motors 0.55-22 KW (IMB 5/IMB 35/IMV 1)
                  • Noise reduced design, form B
                  • Cooling pipes 0.95 - 5.15 KW
                  • 4 model series available (ø200-ø350)
                  • All bell housing lengths comply with VDMA code 24561
                  • The standard bell housing can be replaced easily with a bell housing with oil cooling at any time due to identical installation lengths
                  • Can be used horizontally (IMB 5/IMB 35) as well as vertically (IMV 1)
                  • Foot brackets series PTFL and PTFS mountable acc. to VDMA 24561
            • Heat exchangers

                  • Series EKM Tube bundle oil cooler

                  • Tube bundle with aluminium fins, providing up to 4-times greater cooling surface compared to a standard shell and tube cooler. Cooling
                    capacity up to 230 kW. Extremely pressure resistant –max.: 35 bar. Removeable end caps for easy cleaning of the water pipes. Optionally
                    available with internal bypass valve (patented). Option: seawater version.
                  • SERIES UKC-G OIL/WATER HEAT EXCHANGER

                  • High performance tube bundle cooler for direct mounting into
                    tank or gear box by using existing threaded ports for heaters.
                    Inexpensive and space saving solution incl. cooling surfaces of 0,15 – 0,43 m2 and tube side flow rate of max. 25 l/min by choosing copper-nickel tubes.
                  • Series LKI OI l AIR cooler

                  • Oil air cooler for industrial use. Available in 10 different sizes. Block construction (max. operating pressure 16 bar). 1-way and 2-way. Available with SAE flange. Off-Shore version optional.
                  • Series TFS / A OI l AIR cooler

                  • Compact bypass-flow cooling unit. Combination of motor pump station and oil air cooler in a single unit that operates independently of the actual unit. Pump flange is connected directly to the motor. Extremely low-noise due to internal screw pump. Various installation positions possible. Available in 3 different sizes.
              • SOFTEX® - Elastic couplings

                  • SOFTEX ® -Standard couplings

                    • Torsionally flexible, maintenance- free
                    • Vibration reducing
                    • Axially pluggable
                    • Machined all over – good dynamic properties
                    • Compact design / low flywheel effects
                    • Available hub materials: Aluminium, cast iron (EN-GJL-250, spheroidal cast iron (EN-GJS-400-15), sintered steel and steel
                    • Different elastomer hardness of the gear rings
                    • Bore diameter cylindrical (metric/inch, available tapered or splined acc. to DIN SAE standard
                  • SOFTEX ® -ES NO backlash couplings

                    • Under initial tension no backlash shaft connection
                    • Material: Hubs made of aluminium
                    • Different elastomer hardness of the gear rings
                    • Triple simple cardanic coupling
                    • Axailly pluggable – simple blind mounting, no time-consuming screwings
                    • Small structural dimensions – low flyweehl effects
                    • Maintenance-free
                    • Simple optical test
                    • Available for all usual shaft dimensions
                    • Finish bores acc. to ISO limit and fit H7 (clamp hub F7) keyway from Ø 6 acc. to DIN 6885 P.1-JS9
                  • SOFTEX ® -TL With TAPER Bush

                    • For all driving applications concerning mechanical engineering
                    • Friction-locked solvable shafts/hub connections
                    • Coupling types TL 1/1; TL 2/2 and TL 1/2 possible
                    • Coupling hubs TL 2 axially separable
                    • Application with all standard taper bushes
                  • SOFTEX ® FA FLANGE COUPLINGS

                    • Flange hubs for heavy machinery
                    • All sizes are unmachined on the flange side and available ready for assembly
                    • 2 flanges can be combined or FA flange with standard Softex® hub
                    • Material: Cast Iron (EN-GJL-250)
                • STAREX® - Flexible couplings

                      • STAREX ® FLEXIBLE COUPLINGS

                        • Double cardanic curved tooth gear coupling
                        • Use in general mechanical engeneering and hydraulics
                        • Maintenance-free by combination of materials plastic / steel
                        • Compensation of misalignment of shaft axial-radial-angular
                        • Axially pluggable – simple mounting
                        • Available with finish bore metric H7,taper bore and inch bore as well as toothed wheel work
                        • Base assortment available ex stock
                      • FLEXIBLE FLANGE COUPLINGS
                        STAREX ® -FL-PA

                        • Flange couplings for assembly to combustion engines and hydraulic pumps
                        • Use for all hydrostatic drives of machines for structural engineering, harvesters etc.
                        • High torsional rigidy – operation without resonance
                        • Maintenance-free by combination of materials plastic / steel
                        • Plastic flange with high mechanical strength and temperature dimensional stability (+130 °C)
                        • Extremely short assembly
                        • Simple mounting by axial fitting